Correlation between machining direction, cutter geometry and step-over distance in 3-axis milling: Application to milling by zones. [PDF]
, 2012 Computer-Aided Manufacturing (CAM) occupies an increasingly important role in engineering with all it has to offer in terms of new possibilities and improving designer/manufacturer productivity. The present study addresses machining of free-form surfaces
Senatore, Johanna +3 more
core +1 more source
Journal of Aceh Physics Society, 2021 Abstrak. Pasir alam merupakan bahan alam yang berada ditepi pantai, sungai, maupun perbukitan. Pasir alam merupakan batuan sedimentasi yang mengandung berbagai unsur partikel magnetik dan partikel non-magnetik.
Salomo Sinuraya +3 more
doaj +1 more source
FEM analysis to optimally design end mill cutters for milling of Ti-6Al-4V [PDF]
, 2014 This paper presents an FEM analysis conducted for optimally designing end mill cutters through verifying the cutting tool forces and stresses for milling Titanium alloy Ti-6Al-4V.
Kumar, V +6 more
core +1 more source
The specific selection function effect on clinker grinding efficiency in a dry batch ball mill [PDF]
, 2008 Dry grinding experiments on cement clinker were carried out using a laboratory batch ball mill equipped with a torque measurement. The influence of the ball size distribution on the specific selection function can be approached by laboratory runs using ...
Frances, Christine +2 more
core +1 more source
Amorphization of different furosemide polymorphic forms during ball milling: tracking solid-to-solid phase transformations [PDF]
, 2023 Ball milling is used, not only to reduce the particle size of pharmaceutical powders, but also to induce changes in the physical properties of drugs. In this work we prepared three crystal forms of furosemide (forms Ⅰ, Ⅱ, and Ⅲ) and studied their solid ...
Junbo, Gong +3 more
core +1 more source
Reaction-Ball-Milling-Driven Surface Coating Strategy to Suppress Pulverization of Microparticle Si Anodes [PDF]
, 2018 In this work, we report a novel reaction-ball-milling surface coating strategy to suppress the pulverization of microparticle Si anodes upon lithiation/delithiation. By energetically milling the partially prelithiated microparticle Si in a CO2 atmosphere,
Xiaolei Qu (1414567) +5 more
core +1 more source
An Experimental Study on Milling Titanium Alloy with a Revolving Cycloid Milling Cutter
Applied Sciences, 2020 In this paper, a revolving cycloid milling cutter was designed with a larger effective cutting helix angle and rake angle than a ball end milling cutter of the same diameter.
Guangyue Wang +3 more
doaj +1 more source
Preparation and Tribology Performance of Ni-Al-Ag Self-Lubricating Composite Coatings on Aluminum Alloy [PDF]
Cailiao Baohu, 2023 In order to investigate the existence form of solid lubricant Ag in mechanical ball milling preparation of composite coating and the wide temperature range tribological properties of composite coating，a method of indirectly adding solid lubricant Ag was ...
YAN Chengqi, JIA Zhuying, LI Zhanjun
doaj +1 more source
Microstructure Evolution of Ni-Based ODS Superalloy Powders During Horizontal Rotary Ball Milling
Archives of Metallurgy and Materials, 2017 Microstructure evolution of Ni-based oxide dispersion-strengthened alloy powders with milling time is investigated. The elemental powders having a nominal composition of Ni-15Cr-4.5Al-4W-2.5Ti-2Mo-2Ta-0.15Zr-1.1Y2O3 in wt % were ball-milled by using ...
Lee H.-E. +3 more
doaj +1 more source
Journal of Materials Research and Technology, 2019 In this paper, we report the microstructure and first hydrogenation properties of TiFe cast with 4 wt.% of Zr. Measurements were made in as-cast state and after processing by ball milling and cryomilling.
Peng Lv +3 more
doaj +1 more source