Results 31 to 40 of about 16,179 (262)

Effect of ball milling process on mechanical properties of medical Ti–Mg composites

Fenmo yejin jishu
Ti–15Mg composites were prepared by ball milling, cold pressing, and microwave heating sintering. The effects of ball milling parameters on the properties of the Ti–15Mg mixed powders and the mechanical properties of the sintered composites were studied.
XIA Pengzhao, XU Ying, CAI Yanqing, ZHAO Sitan, SONG Pan   +4 more
doaj   +1 more source

Effect of ball milling and solid solution treatment on microstructure and mechanical properties of ZrMgMo3O12p/2024Al composites

Journal of Materials Research and Technology
The 10 vol% ZrMgMo3O12/2024Al composites were fabricated using the powder metallurgy process and consolidation via vacuum hot pressing. The effects of the ball milling process and solution treatment time on the composites’ microstructure, Vickers ...
Junrui Yang, Guopeng Zhang, Zhongxia Liu, Chaofan Yin, Yuejin Qian, Jianjun Chen   +5 more
doaj   +1 more source

Study and Application of a Wet Ball Milling Ultra-fine Method for Geological Samples

Yankuang ceshi, 2023
BACKGROUNDAt present, there are large particles in geological samples prepared in the laboratory, which affect the representativeness of the samples and the accuracy of the analysis results[1-3].
Xuelin DONG, Zhao XIANG, Zhengxun JIA, Nan ZHANG, Shuoyun TONG, Yuxiang XIONG   +5 more
doaj   +1 more source

Influence of Temperature on the Performance of LiNi1/3Co1/3Mn1/3O2 Prepared by High-Temperature Ball-Milling Method

Advances in Materials Science and Engineering, 2018
Aiming at the preparation of high electrochemical performance LiNi1/3Co1/3Mn1/3O2 cathode material for lithium-ion battery, LiNi1/3Co1/3Mn1/3O2 was prepared with lithium carbonate, nickel (II) oxide, cobalt (II, III) oxide, and manganese dioxide as raw ...
Ming Tian, Xuetian Li, Zhongbao Shao, Fengman Shen   +3 more
doaj   +1 more source

Recycling Chips of Stainless Steel Using a Full Factorial Design

Metals, 2019
The aim of this study was to provide an experimental investigation on the novel method for recycling chips of duplex stainless steel, with the addition of vanadium carbide, in order to produce metal/carbide composites from a high-energy mechanical ...
Claudiney Mendonça, Patricia Capellato, Emin Bayraktar, Fábio Gatamorta, José Gomes, Adhimar Oliveira, Daniela Sachs, Mirian Melo, Gilbert Silva   +8 more
doaj   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Microstructure and anti-oxidation properties of CoNiCrAlY-Al₂O₃ composite coatings based on core-shell structured powder design

Cailiao gongcheng, 2021
The core-shell structured CoNiCrAlY-Al2O3 powders were well-designed and fabricated with the Al2O3 as the shell. The ball milling preparation process of core-shell structured powders was optimized by orthogonal experiment design.
GU Zi-wang, GUO Wen-min, ZHANG Hong-lin, LI Wen-juan   +3 more
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Effects of Freezing Ball Mill Treatment on the Structure and Physicochemical Properties of Oat Starch

Shipin gongye ke-ji
To investigate the effect of freezing ball milling on the structure and physicochemical properties of oat starch, the granule morphology, multiscale structure and physicochemical properties of oat starch were explored by ball milling at different ball ...
Zhongyun ZHAO, Hui XU, Zongjun WU, Shengjun HAN, Zongwei HAO, Yiqun DU, Yaqing XIAO, Yingnan LIU, Kang LIU, Yongquan WANG, Shiyi LI, Mingming ZHENG, Yibin ZHOU, Zhenyu YU   +13 more
doaj   +1 more source

Synergistic effect of Mn substitution and ball milling on NaCu0.2Fe0.8−xMnxO2 cathode materials for sodium-ion batteries [PDF]

RSC Advances
This work focuses on the systematic investigation of the impact of Mn substitution and ball milling on NaCu0.2Fe0.8−xMnxO2 (x = 0.4, 0.5, 0.6, and 0.7) cathodes. The materials were synthesized using the conventional solid-state method.
Ichrak Ben Slima, Kawthar Trabelsi, Lahcen Fkhar, Karim Karoui, Frédéric Boschini, Abdallah Ben Rhaiem, Abdelfattah Mahmoud   +6 more
doaj   +1 more source