Effect of ball milling process on microstructure and mechanical properties of CNTs/Al composites
Fenmo yejin jishuCarbon nanotubes (CNTs) and aluminum composite powders were prepared by both wet ball milling and dry ball milling. The CNTs reinforced aluminum matrix (CNTs/Al) composites were fabricated by sparking plasma sintering (SPS) combined with hot extrusion ...
YOU Yuanqi +5 more
doaj +1 more source
Shipin gongye ke-ji, 2022 Flavonoids in peanut hull were extracted by the ball milling method. The effects of solid-liquid ratio, ball milling time, and ethanol volume fraction on the extraction yield of flavonoids were investigated by single factor experiments.
Dongcan LV +5 more
doaj +1 more source
Amorphization and evolution of magnetic properties during mechanical alloying of Co62Nb6Zr2B30: Dependence on starting boron microstructure [PDF]
, 2007 Co62Nb6Zr2B30 composition was mechanically alloyed using three different types of boron powders in the starting mixture: crystalline β-B, commercial amorphous B and optimized amorphous B via ball milling.
A. Barton +6 more
core +3 more sources
Study and Application of a Wet Ball Milling Ultra-fine Method for Geological Samples
Yankuang ceshi, 2023 BACKGROUNDAt present, there are large particles in geological samples prepared in the laboratory, which affect the representativeness of the samples and the accuracy of the analysis results[1-3].
Xuelin DONG +5 more
doaj +1 more source
Low-Temperature Rapid Synthesis and Superconductivity of Fe-Based Oxypnictide Superconductors
, 2010 we were able to develop a novel method to synthesize Fe-based oxypnictide superconductors. By using LnAs and FeO as the starting materials and a ball-milling process prior to solid-state sintering, Tc as high as 50.7 K was obtained with the sample of Sm ...
Artioli G. A. +7 more
core +1 more source
Effect of ball milling process on mechanical properties of medical Ti–Mg composites
Fenmo yejin jishuTi–15Mg composites were prepared by ball milling, cold pressing, and microwave heating sintering. The effects of ball milling parameters on the properties of the Ti–15Mg mixed powders and the mechanical properties of the sintered composites were studied.
XIA Pengzhao +4 more
doaj +1 more source
Big Data on Decision Making in Energetic Management of Copper Mining [PDF]
, 2016 Indexado en: Web of Science; Scopus.It is proposed an analysis of the related variables with the energetic consumption in the process of concentrate of copper; specifically ball mills and SAG.
Carrasco, R +5 more
core +2 more sources
Journal of Materials Research and TechnologyThe 10 vol% ZrMgMo3O12/2024Al composites were fabricated using the powder metallurgy process and consolidation via vacuum hot pressing. The effects of the ball milling process and solution treatment time on the composites’ microstructure, Vickers ...
Junrui Yang +5 more
doaj +1 more source
The role of boron oxide and carbon amounts in the mechanosynthesis of ZrB2-SiC-ZrC nanocomposite via a self-sustaining reaction in the zircon/magnesium/boron oxide/graphite system [PDF]
, 2014 Herein, ZrSiO4/B2O3/Mg/C system was used to synthesize a ZrB2-based composite by means of a high energy ball milling process. A mechanically induced selfsustaining reaction was achieved in this system. A nanocomposite powder of ZrB2– SiC–ZrC was prepared
Bafghi, M. Sh +3 more
core +1 more source
Advances in Materials Science and Engineering, 2018 Aiming at the preparation of high electrochemical performance LiNi1/3Co1/3Mn1/3O2 cathode material for lithium-ion battery, LiNi1/3Co1/3Mn1/3O2 was prepared with lithium carbonate, nickel (II) oxide, cobalt (II, III) oxide, and manganese dioxide as raw ...
Ming Tian +3 more
doaj +1 more source