Results 51 to 60 of about 309,791 (349)

MgO-based adsorbents for CO2 adsorption: Influence of structural and textural properties on the CO2 adsorption performance [PDF]

, 2017
MgO-based adsorbents for CO2 adsorption: Influence of structural and textural properties on the CO2 adsorption performanceA series ofMgO-based adsorbents were prepared through solution–combustion synthesis and ball-milling process. The prepared MgO-based
GRANADOS CORREA, FRANCISCO, GRANADOS CORREA, FRANCISCO, GUTIERREZ BONILLA, ELVIRA, GUTIERREZ BONILLA, ELVIRA, MORALES LUCKIE, RAUL ALBERTO, MORALES LUCKIE, RAUL ALBERTO, Sánchez Mendieta, Víctor, Sánchez Mendieta, Víctor   +7 more
core   +1 more source

Effect of ball milling and solid solution treatment on microstructure and mechanical properties of ZrMgMo3O12p/2024Al composites

Journal of Materials Research and Technology
The 10 vol% ZrMgMo3O12/2024Al composites were fabricated using the powder metallurgy process and consolidation via vacuum hot pressing. The effects of the ball milling process and solution treatment time on the composites’ microstructure, Vickers ...
Junrui Yang, Guopeng Zhang, Zhongxia Liu, Chaofan Yin, Yuejin Qian, Jianjun Chen   +5 more
doaj   +1 more source

Influence of Temperature on the Performance of LiNi1/3Co1/3Mn1/3O2 Prepared by High-Temperature Ball-Milling Method

Advances in Materials Science and Engineering, 2018
Aiming at the preparation of high electrochemical performance LiNi1/3Co1/3Mn1/3O2 cathode material for lithium-ion battery, LiNi1/3Co1/3Mn1/3O2 was prepared with lithium carbonate, nickel (II) oxide, cobalt (II, III) oxide, and manganese dioxide as raw ...
Ming Tian, Xuetian Li, Zhongbao Shao, Fengman Shen   +3 more
doaj   +1 more source

Recycling Chips of Stainless Steel Using a Full Factorial Design

Metals, 2019
The aim of this study was to provide an experimental investigation on the novel method for recycling chips of duplex stainless steel, with the addition of vanadium carbide, in order to produce metal/carbide composites from a high-energy mechanical ...
Claudiney Mendonça, Patricia Capellato, Emin Bayraktar, Fábio Gatamorta, José Gomes, Adhimar Oliveira, Daniela Sachs, Mirian Melo, Gilbert Silva   +8 more
doaj   +1 more source

Microstructure and anti-oxidation properties of CoNiCrAlY-Al₂O₃ composite coatings based on core-shell structured powder design

Cailiao gongcheng, 2021
The core-shell structured CoNiCrAlY-Al2O3 powders were well-designed and fabricated with the Al2O3 as the shell. The ball milling preparation process of core-shell structured powders was optimized by orthogonal experiment design.
GU Zi-wang, GUO Wen-min, ZHANG Hong-lin, LI Wen-juan   +3 more
doaj   +1 more source

Working Volume and Milling Time on the Product Size/Morphology, Product Yield, and Electricity Consumption in the Ball-Milling Process of Organic Material

Indonesian Journal of Science and Technology, 2018
Analysis of ball-milling process under various conditions (i.e. working volume, milling time, and material load) on the material properties (i.e. chemical composition, as well as particle size and morphology), product yield, and electricity consumption ...
A. Nandiyanto, Riezqa Andika, Muhammad Aziz, L. Riza   +3 more
semanticscholar   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

The Mechanical Alloying Behavior of Fe2O3 into NiO in the High-Energy Ball-Milling Process

Advances in Materials Science and Engineering, 2021
The NiO and Fe2O3 powders were mixed by the high-energy ball-milling, followed by a sintering of the mixture at 1340°C for 0.5 h. XRD, SEM, DSC, and size measurements were preformed to study the microstructure evolution in the high-energy ball-milled ...
Y. Z. Zhu, Y. Liu, H. Huang, Y. Y. Guo, S. Y. Yin, F. W. Hu   +5 more
doaj   +1 more source

Fabrication of aluminum matrix composites reinforced with nano- to micrometer-sized SiC particles [PDF]

, 2016
In this study, the hot extrusion process was applied to stir cast aluminum matrix–SiC composites in order to improve their microstructure and reduce cast part defects. SiC particles were ball milled with Cr, Cu, and Ti as three forms of carrier agents to
Azari Khosroshahi, Rasoul, Brabazon, Dermot, Taherzadeh Mousavian, Reza, Yazdani, S.   +3 more
core   +1 more source

An environmentally friendly ball milling process for recovery of valuable metals from e-waste scraps.

Waste Management, 2017
The present study reports a mechanochemical (MC) process for effective recovery of copper (Cu) and precious metals (i.e. Pd and Ag) from e-waste scraps. Results indicated that the mixture of K2S2O8 and NaCl (abbreviated as K2S2O8/NaCl hereafter) was the ...
Zhi-yuan Zhang, Fu-Shen Zhang, Tianqi Yao   +2 more
semanticscholar   +1 more source