Results 11 to 20 of about 8,304,922 (298)

Regularities of changing the dimensions of the main bore of the cylinder of TMZ-450D diesel engine during the technological process

open access: yesЗаписки Горного института, 2021
The article deals with the problems arising during the mechanical and thermal treatment of the TMZ-450D diesel engine cylinder, which is the base part of the engines of small-sized generators and compressors, which are widely used for mobile units in the
Alexander S. Yamnikov   +1 more
doaj   +1 more source

Wuzi Yanzong Pill relieves CPZ-induced demyelination by improving the microenvironment in the brain

open access: yesHeliyon, 2022
Ethnopharmacology relevance: Wuzi Yanzong Pill (WYP), a well-known prescription for invigorating the kidney and essence, which is widely used to treat infertility such as oligoasthenospermia.
Yan-Rong Li   +10 more
doaj   +1 more source

GSK3β-dependent lysosome biogenesis: An effective pathway to mitigate renal fibrosis with LM49

open access: yesFrontiers in Pharmacology, 2022
Renal fibrosis is an incurable disorder characterised by an imbalance of the extracellular matrix (ECM) favouring excess production over degradation.
Jinhong Ren   +13 more
doaj   +1 more source

5,2′-Dibromo-2,4′,5′-trihydroxydiphenylmethanone Inhibits LPS-Induced Vascular Inflammation by Targeting the Cav1 Protein

open access: yesMolecules, 2022
Vascular inflammation is directly responsible for atherosclerosis. 5,2′-Dibromo-2,4′,5′-trihydroxydiphenylmethanone (TDD), a synthetic bromophenol derivative, exhibits anti-atherosclerosis and anti-inflammatory effects.
Hongxia Yuan   +6 more
doaj   +1 more source

Preventing development of post-stroke hyperexcitability by optogenetic or pharmacological stimulation of cortical excitatory activity

open access: yesNeurobiology of Disease, 2023
Stroke is the most common cause of acquired epilepsy, but treatment for preventing the development of post-stroke epilepsy is still unavailable. Since stroke results in neuronal damage and death as well as initial loss of activity in the affected brain ...
Yadav Adhikari   +3 more
doaj   +1 more source

Schiff base-mediated base pairing [PDF]

open access: yesNucleic Acids Symposium Series, 2005
We here present a novel covalently linked base pair via Schiff base formation between 5-formyluracil (fU) and 5-aminocytosine (AmC). The formation of Schiff base remarkably increases thermal stability of the duplex DNA, whereas it completely dissociates upon heating at 90 degrees C. Neither AmC nor fU produces covalent linkage with other natural bases,
Chikara, Dohno   +2 more
openaire   +2 more sources

The Chemical Constituents of Diaphragma Juglandis Fructus and Their Inhibitory Effect on α-Glucosidase Activity

open access: yesMolecules, 2022
In our current investigation, 37 constituents (1–37), including 11 megastigmanes (1–11), 17 flavonoids (12–28) and 9 phenylpropanoids (29–37), were isolated from a 70%-EtOH extract of Diaphragma juglandis Fructus.
Jinyan Tan   +7 more
doaj   +1 more source

Making Operation-Based CRDTs Operation-Based [PDF]

open access: yesProceedings of the First Workshop on Principles and Practice of Eventual Consistency, 2014
Conflict-free Replicated Datatypes (CRDT) are usually classified as either state-based or operation-based. However, the standard definition of op-based CRDTs is very encompassing, allowing even sending the full-state, blurring the distinction. We introduce pure op-based CRDTs, that can only send operations to other replicas, drawing a clear distinction
Baquero, Carlos   +2 more
openaire   +4 more sources

Parametric design process basing on building physical performance [PDF]

open access: yesE3S Web of Conferences, 2019
The purpose of this research is to investigate general workflow of parametric architecture design basing on building physical performance. Earlier study on parametric design have shown that this method can effectively improve quality and diversity in ...
Li Yangluxi, Chen Lei
doaj   +1 more source

Development of technological process of metal machining from stamping on 5-axis CNC milling machine [PDF]

open access: yesE3S Web of Conferences, 2023
The technological process of compressor working blade production from stamping with minimum allowance for machining of the working part, on 5-axis CNC machine aimed at reducing the units of machine equipment has been developed. The tooling for basing the
Detkin A. V.   +2 more
doaj   +1 more source

Home - About - Disclaimer - Privacy