Results 51 to 60 of about 5,751 (259)

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

Advanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Influence of time on the small strain shear modulus of an allophanic volcanic ash [PDF]

E3S Web of Conferences
The small strain shear modulus is an important parameter in the assessment of soil dynamics problems. Studies on the small strain shear stiffness of volcanic ash remain rare probably because globally they cover just under 1% of the land surface. However,
Gobin Mukteshwar, Yasufuku Noriyuki, Watanabe Midori, Liu Guojun, Ishikura Ryohei   +4 more
doaj   +1 more source

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Small-strain stiffness of selected anthropogenic aggregates from bender element tests

Studia Geotechnica et Mechanica
This article presents a study on the stiffness of mixtures of anthropogenic materials derived from construction or demolition waste, specifically fine recycled concrete aggregates (fRCAs) with different fine fraction (FF) contents. The study investigated
Gabryś Katarzyna, Markowska-Lech Katarzyna, Sas Wojciech   +2 more
doaj   +1 more source

Dynamic and static measurements of small strain moduli of toyoura sand

Revista Facultad de Ingeniería Universidad de Antioquia, 2014
A series of triaxial tests were performed on specimens made of Toyoura sand having different dry densities. Very small unloading/ reloading cycles were applied to obtain “static” Young’s modulus.
Manuel Builes, Edwin García, Carlos Alberto Riveros   +2 more
doaj   +1 more source

Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines

Advanced Engineering Materials, EarlyView.
Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl, Daniel Emil Mack, Martin Tandler, Susanne Schrüfer, Robert Vaßen   +4 more
wiley   +1 more source

Improved Evaluation of Bender Element Testing for Different Confinement Stress Levels

e-Journal of Nondestructive Testing
Accurate material characterization over time is crucial for the safety, efficiency, and sustainability of energy and environmental projects, as well as infrastructure resilience.
Chehem Vargas-Neuville, Kamelia Atefi-Monfared, Giovanni Cascante   +2 more
doaj   +1 more source