Results 31 to 40 of about 13,474 (218)
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
Инженерно-строительный журнал, 2014 In steel structures, the combination of both a bending moment and bimoment actions on I-beam members is possible in many cases. In the elastic stage of work, the material bearing capacity check is based on maximum normal stresses, which for symmetric I ...
A.R. Tusnin, M. Prokic
doaj +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley +1 more source
Probabilistic model for prestressed precast concrete T-beam
Tạp chí Khoa học Đại học Mở Thành phố Hồ Chí Minh - Kỹ thuật và Công nghệ, 2019 This article evaluates the calculation of bending resistance to time of a prestressed precast concrete T-beam using a newlybuilt simple probabilistic model.
Lê Đức Tuấn
doaj +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
Long-term Loads based on Evaluation of Resistance and Seakeeping Performances for a Desalination Plant Ship [PDF]
한국해양공학회지, 2019 Desalination plant ships have been recently regarded as one of the probable solutions for drought seasons in many countries. Because desalination plants should be mounted on the desalination ships and special purpose storages such as salty waste water ...
Jae-bin Lee +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan +5 more
wiley +1 more source
Development of a software for the numerical modeling of reinforced concrete sections - AlfaMCV
SoftwareX, 2020 In the design of reinforced concrete structures, the usual procedure is the inclusion of safety factors, according to the Brazilian Standards, to allow the structure to withstand loads above the ones predicted and a possible collapse.
Ana Waldila de Queiroz Ramiro Reis +2 more
doaj +1 more source