Results 51 to 60 of about 3,934,471 (229)

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal   +2 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev   +2 more
wiley   +1 more source

Analysis of Mechanical Behavior of Different Needle Tip Shapes During Puncture of Carbon Fiber Fabric

open access: yesAUTEX Research Journal, 2021
In the present study, the fiber-bending around the needle during the piercing process of the carbon fabric is investigated. In this regard, a mathematical model is established to investigate the bending elongation of the carbon fiber around the needle ...
Yang Jingzhao   +3 more
doaj   +1 more source

I‐beam‐to‐SHS column moment resisting joints using passing‐through plates under opposite bending moments: numerical and analytical studies

open access: yesce/papers, 2023
Abstract As thin walled HSS columns are very flexible, they usually exhibit excessive deformation when resisting a bending moment or transverse loads. Adding exterior/interior diaphragms is one way to remedy the problem. Another option that can significantly increase strength and stiffness is to allow passing plates through the hollow
Mouad MADHOUNI   +3 more
openaire   +1 more source

Stage-by-stage control effect field analysis of steel material servo enhanced support system on lateral displacement and bending moment during deep basement excavation

open access: yesCase Studies in Construction Materials, 2022
This study enumerates the stage-by-stage usefulness of the addition of a servo system to the lateral steel support system to improve the lateral load resistance of steel support members on an actual deep excavation site.
Horris K. Nangulama   +4 more
doaj   +1 more source

Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy

open access: yesAdvanced Engineering Materials, EarlyView.
Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang   +6 more
wiley   +1 more source

BENDING MOMENT RESISTANCE OF L-SHAPED TWO-GUSSET-PLATE FURNITURE JOINTS IN ORIENTED STRANDBOARD [PDF]

open access: yes, 2014
Bending moment resistances of L-shaped joints connected with two gusset plates stapled on one side of joint members in oriented strandboard (OSB) were investigated. Factors were joint member material type, rail width, and number of staples.
Zhang, Jilei, DEMİREL, SAMET
core   +2 more sources

Behavior of Longitudinal Plate to Circular Hollow Section Welded Joint Under In-Plane Bending Moment [PDF]

open access: yesMSA Engineering Journal
Connections between steel beams and Circular Hollow Section (CHS) columns using welded longitudinal plates are commonly adopted due to their cost-efficiency compared to passing-through plate techniques.
Eman Sayed
doaj   +1 more source

Experimental Analysis of Recycled Aggregate Concrete Beams and Correction Formulas for the Crack Resistance Calculation

open access: yesAdvances in Materials Science and Engineering, 2022
This paper studies the similarities and the differences between natural aggregate concrete (NAC) beams and recycled aggregate concrete (RAC) beams in terms of concrete material properties, bearing capacity, and crack resistance and further proposes ...
Xuyong Chen   +5 more
doaj   +1 more source

Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System

open access: yesAdvanced Engineering Materials, EarlyView.
Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner   +7 more
wiley   +1 more source

Home - About - Disclaimer - Privacy