Results 1 to 10 of about 10,216,586 (160)
Bending Properties of an Extensile Fluidic Artificial Muscle [PDF]
Frontiers in Robotics and AI, 2022 Low stiffness, large stroke, and axial force capabilities make Extensile Fluidic Artificial Muscles (EFAMs) a feasible soft actuator for continuum soft robots.
Jacek Garbulinski, Norman M. Wereley
doaj +2 more sources
Study of ternary deep eutectic solvents to enhance the bending properties of ash wood. [PDF]
RSC AdvDeep eutectic solvents (DESs) are considered one of the most promising biomass pretreatment reagents, and their research applications in woody fibrous biomass are increasing yearly.
Bai R, Wang W, Chen M, Wu Y.
europepmc +2 more sources
Determination of the Bending Properties of Wire Rope Used in Cable Barrier Systems. [PDF]
Materials (Basel), 2020 This paper presents research on the bending properties of 3 × 7 19-mm wire rope commonly used in road cable barriers. A total of 19 experimental tests were conducted.
Bruski D.
europepmc +2 more sources
Effects of Temperature on Bending Properties of Three-Dimensional and Five-Directional Braided Composite. [PDF]
Molecules, 2019 The bending properties of three-dimensional (3Dim) and five-directional (5Dir) braided/epoxy resin composites at room temperature, 90 °C, 110 °C, and 150 °C and heating for 0.25 h, 10 h, and 30 h, respectively, were studied.
Li P, Jia N, Pei X, Wan Z, Li J, Wu H.
europepmc +2 more sources
Influence of Defects on Bending Properties of 2D-T700/E44 Composites Prepared by Improved Compression Molding Process. [PDF]
Materials (Basel), 2018 2D-T700/E44 composite materials were prepared by improved compression molding process (ICM) then microstructure and properties of the composites were analyzed and summarized by scanning electron microscope (SEM) and electronic universal testing machine ...
Ma Y, Li S, Wang J, Ju L, Liu X.
europepmc +2 more sources
Characterization of three-point bending properties of metal-resin interpenetrating phase composites. [PDF]
RSC Adv, 2018 Metal–resin composites provide improved combinations of mechanical properties of raw materials. A novel metal–resin interpenetrating phase composite (IPCs) has been fabricated by spontaneously infiltrating unsaturated polyester resin into porous short ...
Yao B, Zhou Z, Duan L, Chen Z.
europepmc +2 more sources
Multilayer stag beetle elytra perform better under external loading via non-symmetric bending properties. [PDF]
J R Soc Interface, 2018 Insect cuticle has drawn a lot of attention from engineers because of its multifunctional role in the life of insects. Some of these cuticles have an optimal combination of lightweight and good mechanical properties, and have inspired the design of ...
Kundanati L +4 more
europepmc +2 more sources
Composites Part A: Applied Science and Manufacturing, 2018 To enhance the bending properties of carbon fiber-reinforced thermoplastics (CFRTPs) by improving their interfacial properties, a new colloidal technique has been developed in this work.
Tetsuya Yamamoto, Toshihira Irisawa
exaly +2 more sources
Journal of Materials Research and TechnologySignificant improvement of bending properties (approximately 64.7%) for WE43 magnesium alloy was realized by weakening the basal texture and raising the deformation temperature. The mechanisms for such improvement were investigated in detail by combining
Wenzhuo Xie +10 more
doaj +3 more sources
Buildings, 2023 Salvaged timber elements often have length limitations, and therefore, their reuse in structural products normally would require additional processing and end-to-end joining.
L. Giordano, M. Derikvand, G. Fink
semanticscholar +1 more source