Results 51 to 60 of about 145,595 (309)
Vibration and buckling of thin-walled composite I-beams with arbitrary lay-ups under axial loads and end moments [PDF]
, 2013 A finite element model with seven degrees of freedom per node is developed to study vibration and buckling of thin-walled composite I-beams with arbitrary lay-ups under constant axial loads and equal end moments.
Lee, Jaehong, Vo, Thuc
core +1 more source
Bending strength of magnesium oxide board
, 2021 Magnesium Oxide (MgO) board has been widely used in prefabricated lightweight steel frame wall systems and as the floor board covering component.
Tang, Hing Kwong +3 more
core +1 more source
Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines
Advanced Engineering Materials, EarlyView.Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl +4 more
wiley +1 more source
Effect of Freezing Temperature on Impact Bending Strength and Shore-D Hardness of Some Wood Species
BioResources, 2022 Wood is exposed to variable environmental conditions during its use. Low temperature is one of the most important environmental factors affecting the behavior of wood in use.
Osman Emre Özkan
doaj +2 more sources
Maderas: Ciencia y Tecnología, 2015 The aim of this study is to determine the change of some physical properties (oven-dry density, weight loss, swelling and anti-swelling efficiency) and mechanical properties (compression strength parallel to grain, bending strength, modulus of elasticity
Süleyman Korkut, Ayhan Aytin
doaj
Bending technology of high strength steel sheets and tools for its realization
Литьë и металлургия, 2020 The article proposes and theoretically justifies a method for bending high-strength steels with compression. The technology allows to get parts from high-strength steels without cracks along the bending line.
V. A. Tаmilа, M. L. Nesterovich
doaj +1 more source
A Study of the Effects of height and Thickness of Tenon Made Out of Beech and Hornbeam on bending Strength of Mortise and tenon joint [PDF]
تحقیقات علوم چوب و کاغذ ایران, 2010 The aim of this study was investigating the parameters of mortise and tenon joint made out of beech and hornbeam and develop formula to estimate ultimate bending strength.
Jamail Visi +2 more
doaj +1 more source
Numerical Simulation of Material Strength Deterioration due to Pitting Corrosion [PDF]
, 2014 Pitting corrosion is an insidious form of localized corrosion affecting characteristics of various engineering metallic alloys. Currently very limited literature exists with regard to systematic characterization of pitted surfaces or the efficient use of
Salonitis, Konstantinos +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
BioResources, 2014 This study designed composite wooden construction elements strengthened with woven wire fiberglass netting and determined the technical attributes. Scots pine (Pinus sylvestris L.) was used in wooden layers, and woven wire fiberglass netting was used in ...
Abdullah Togay, Emre Ergin
doaj +1 more source