Results 81 to 90 of about 181,339 (261)
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
A size-dependent functionally graded sinusoidal plate model based on a modified couple stress theory [PDF]
, 2013 A size-dependent model for bending and free vibration of functionally graded plate is developed based on the modified couple stress theory and sinusoidal shear deformation theory.
Thai, Huu-Tai, Vo, Thuc
core +1 more source
Wood-based Corrugated Core Sandwich Panels Manufactured Using a Wooden Mold
BioResources, 2023 A wooden matched-die mold was manufactured to develop wood-based corrugated panels. Wood veneers brushed with resin were cold pressed between the mold halves and formed into a corrugated geometry.
Mostafa Mohammadabadi +4 more
doaj
Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales
Advanced Engineering Materials, EarlyView.Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik +7 more
wiley +1 more source
An Experimental Study on the Impact Bending Strength Test
, 1974 Many experimental studies to know the behavior of materials under the impact compression or tension have been carried out. On the impact bending, however, test methods under the consideration of strain rate and bending moment rate have been little ...
Hatake, Yoshikatsu +8 more
core +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
Optimizing Lumber Densification for Mitigating Rolling Shear Failure in Cross-Laminated Timber (CLT)
Construction MaterialsRolling shear in cross-laminated timber (CLT) has been identified as the governing factor influencing design value. Likewise, densification has been found to be an effective method of enhancing the rolling shear strength of lumber and in turn, CLT.
Suman Pradhan +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič +7 more
wiley +1 more source
Assessment of a Cyclic Bending Test Method for Printed Flexible Supercapacitor
, 2022 Printed flexible supercapacitor (SC) is seen as an attractive alternative to replace batteries as energy storage unit in energy autonomous sensors. This paper assesses a cyclic bending test method for printed flexible SC. The test is evaluated using four
Jauho, Aarne +5 more
core +1 more source
Analysis of the initial deformabiliti of austenitic stainless stells with a bend test
Metalurgija, 2019 Austenitic stainless steel solidify under non-equilibrium conditions, and form two-phase microstructure of austenite and δ-ferrite. Workability of steels in hot are better in the primary crystallization of δ-ferrite. The influence of chemical composition
B. Arh +4 more
doaj