Results 1 to 10 of about 7,227 (151)
Rolling Shear Strength of Cross Laminated Timber (CLT)—Testing, Evaluation, and Design
Buildings, 2023 Cross laminated timber (CLT), with its typical orthogonal layering and exposure to out-of-plane bending, develops inherent rolling shear stresses. These stresses need to be checked during the ultimate limit state design process. With the ongoing revision
David Glasner +3 more
doaj +4 more sources
The Influence of Panel Lay-Up on the Characteristic Bending and Rolling Shear Strength of CLT [PDF]
Buildings, 2018 The objective of this study was to characterise the behaviour of cross laminated timber (CLT) panels and the influence of the panel lay-up on the failure strength.
Conan O’Ceallaigh +2 more
doaj +6 more sources
Journal of Materials Research and TechnologyThis study reports the preparation of medium-thickness aluminum/steel composite plates with different diffusion layers using rheological cast-rolling technology.
Jin Qiu +5 more
doaj +4 more sources
Rolling shear modulus and strength of beech wood laminations
Holzforschung, 2016 Abstract Previous research indicated that the rolling shear properties of European beech wood (Fagus sylvatica) are considerably higher than those of softwood. The aim of the presented investigation was to substantiate previous data on rolling shear modulus and strength of European beech wood and to further evaluate its substitution of ...
Simon Aicher
exaly +2 more sources
Evaluation of the effect of knots on rolling shear strength of cross laminated timber (CLT)
Construction and Building Materials, 2019 Abstract The study experimentally and analytically investigated the effect of knots on the rolling shear (RS) strength of 3-ply southern yellow pine cross-laminated timber (CLT). Center-point bending tests and two-plate shear tests were conducted on six CLT configurations composed of different types of cross layer laminations based on knots ...
Jason Street +2 more
exaly +4 more sources
Influence of Lamination Aspect Ratios and Test Methods on Rolling Shear Strength Evaluation of Cross-Laminated Timber [PDF]
Journal of Materials in Civil Engineering, 2019 AbstractRolling shear (RS) strength may govern load-carrying capacity of cross-laminated timber (CLT) subjected to high out-of-plane loading because high RS stresses may be induced in cross layers ...
Minghao Li +2 more
exaly +3 more sources
Applied SciencesTo increase and optimize the use of wood in structural elements, a deep understanding of its mechanical behavior is necessary. The transverse material properties of wood are particularly important for mass timber construction and for utilizing wood as a ...
Shaheda T. Akter +2 more
doaj +3 more sources
A study on the effect of grain morphology on shear strength in granular materials [PDF]
EPJ Web of Conferences, 2021 The Discrete Element Method (DEM) has been successfully used to further understand GM behaviour where experimental means are not possible or limited. However, the vast majority of DEM publications use simplified spheres with rolling friction to account ...
Govender Nicolin, Pizette Patrick
doaj +1 more source
Shear strength and force transmission in granular media with rolling resistance [PDF]
Physical Review E, 2008 We investigate a class of granular materials characterized by the possibility of interlocking between the particles. The interlocking is modeled by its effect through rolling resistance depending on relative rotation and normal force at the contact points and involving a single parameter analogous to the sliding friction coefficient.
Estrada, Nicolas +2 more
openaire +3 more sources
Shear strength properties of hybrid (hinoki cypress and Japanese cedar) cross-laminated timber
Journal of Wood Science, 2021 In this study, the out-of-plane shear strength of hybrid cross-laminated timber (CLT) with outer layers of hinoki (hinoki cypress, Chamaecyparis obtusa) and inner layers of sugi (Japanese cedar, Cryptomeria japonica) is investigated for four different ...
Seiichiro Ukyo +3 more
doaj +1 more source