Results 21 to 30 of about 2,441,995 (263)
Interfacial microstructure and shear strength of Ti-6Al-4V/TiAl laminate composite sheet fabricated by hot packed rolling [PDF]
, 2011 A two layer Ti-6Al-4V(wt%)/Ti-43Al-9V-Y(at%) laminate composite sheet with a uniform interfacial microstructure and no discernible defects at the interfaces has been prepared by hot-pack rolling, and its interfacial microstructure and shear strength were
Chen, Yuyong +5 more
core +1 more source
Metals, 2020 The effect of rolling temperatures on the interface microstructure and mechanical properties is investigated using 2-mm-thick TA1/Q235B composite sheets, which were prepared after nine passes of hot rolling of explosive welded plates.
Huizhong Li +6 more
doaj +1 more source
Rolling contact fatigue of silicon nitride. [PDF]
Silicon Nitride has traditionally been used as rolling contact bearing material owing to its superior performance compared to bearing steels. Its successful application as a bearing element has led to the development of Silicon Nitride in other rolling ...
Wang, W.
core +6 more sources
Journal of Materials Research and Technology, 2023 6061 aluminum (Al) alloys were asymmetrically rolled to apply shear deformation, and the effects of pre/post-aging treatment on the mechanical properties and texture evolution were analyzed.
Wonkee Chae +8 more
doaj +1 more source
Evaluation of rolling shear strength of plywood by flexural vibration method
Journal of Wood Science, 1998 The rolling shear strength of plywood was evaluated using a flexural vibration test. Test specimens were lauan and Douglas fir three-ply plywoods made from thick veneers. The dynamic shear and Young's moduli were determined using the flexural vibration method, which involved in-plane and out-of-plane flexural vibration.
Heng Xu +4 more
openaire +1 more source
Structural Properties of Commercial Australian Plantation Hardwood CLT
Buildings, 2023 Significant volumes of plantation hardwood are available in Australia to produce value-added engineered wood products such as cross-laminated timber (CLT).
Mateo Gutierrez +3 more
doaj +1 more source
Microstructure and bonding properties of hot-rolled 7075/AZ31B clad sheets
工程科学学报, 2020 Magnesium/aluminum (Mg/Al) bimetallic laminated composites have attracted considerable attention because of their excellent properties. Mg alloys are lightweight structural metals with low density and excellent properties such as high stiffness-to-weight
Zong-he WU +4 more
doaj +1 more source
Numerical simulation of direct shear test of sand considering rotational impedance
Shuili Shuiyun Gongcheng Xuebao, 2021 A series of sand direct shear numerical simulation tests were performed using the discrete element method, so as to investigate the inherent relation of meso-mechanics between the particle’s rotation-resistant capacity and the interaction of sands and ...
WANG Zhuang +3 more
doaj +1 more source
Dimerization of a selectin and its ligand stabilizes cell rolling and enhances tether strength in shear flow [PDF]
Proceedings of the National Academy of Sciences, 2001 Selectins mediate rolling of leukocytes by rapid formation and dissociation of selectin–ligand bonds, which are assumed to require high mechanical strength to prevent premature dissociation by the forces applied in shear flow. This assumption is based largely on the observation that increasing wall shear stress increases only modestly the dissociation ...
V, Ramachandran +7 more
openaire +2 more sources
Journal of Materials Research and Technology, 2023 Cu/Al corrugated laminated composites were prepared by corrugated cold roll bonding (CCRB), and the deformation behavior and bonding properties of the laminated composites were investigated by experimental research and numerical simulation.
Gao Xiangyu +5 more
doaj +1 more source