Results 201 to 210 of about 6,076 (251)

Biaxial testing of composite tubes

Experimental Mechanics, 1985
The development of a tubular test specimen for the characterization of advanced composite-material lamina and laminate mechanical properties is presented. The specimen design and supporting analyses are given for a practical tubular specimen that minimizes end effects.
G. R. Toombes, S. R. Swanson, D. S. Cairns   +2 more
openaire   +1 more source

The Biaxial Wheel Test Rig

SAE Technical Paper Series, 1985
<div class="htmlview paragraph">Operating load simulation tests are presently to the greatest extent the state of engineering for the development of new running gear components, because of their great strength of statement. These genuine operating load simulation tests on car wheels are only possible with relatively expensive test rigs.</div ...
Helmut G. Naundorf, Siegfried J. Angerer, Peter R. Hutmann   +2 more
openaire   +1 more source

Biaxial tensile tests of the porcine ascending aorta

Journal of Biomechanics, 2016
One of the aims of this work is to develop an original custom built biaxial set-up to assess mechanical behavior of soft tissues. Stretch controlled biaxial tensile tests are performed and stereoscopic digital image correlation (SDIC) is implemented to measure the 3D components of the generated displacements.
Deplano, Valérie, Boufi, Mourad, Boiron, Olivier, Guivier-Curien, Carine, Alimi, Yves, Bertrand, Eric   +5 more
openaire   +3 more sources

Appraisal of biaxial strength testing

Journal of Non-Crystalline Solids, 1980
Abstract Three biaxial strength tests (ring-on-ring, piston-on-3 ball, and ball-on-ring) were evaluated using finite element analysis. Although in all three tests some uncertainties exist regarding the calculation of fracture stresses from the analytical equation, if fracture occurs within the loading ring, the ring-on-ring loading is thought to give
J.E. Ritter, K. Jakus, A. Batakis, N. Bandyopadhyay   +3 more
openaire   +1 more source

Development of a Biaxial Test Fixture

1980
Abstract : The Aerospace Structures Information and Analysis Center has designed and fabricated a specimen load system for conducting biaxial material characterizations of composite materials. In particular, the system is useful for determining a major portion of the biaxial failure envelopes for composite materials.
Warren Gibson, Neil Holt
openaire   +1 more source

Biaxial Wheel Fatigue Test

2021
<div class="section abstract"> <div class="htmlview paragraph">This SAE Recommended Practice provides uniform laboratory procedures for biaxial fatigue testing of wheels intended for normal highway use and temporary use on passenger car vehicles and light trucks and minimum cycle requirement for ferrous wheels for ballasted passenger car ...
openaire   +1 more source

A Biaxial Apparatus for Testing Soils

Geotechnical Testing Journal, 1990
Abstract A biaxial compression apparatus for investigating shear-band formation and growth in dry and water-saturated sand and clay specimens is described. This apparatus is a modification of the device designed by Vardoulakis and Goldscheider [1] for testing planar shear banding in sands.
A Drescher, I Vardoulakis, C Han
openaire   +1 more source

Biaxial Testing of Repaired Concrete

ACI Materials Journal, 1992
In this work, a special biaxial testing set up is designed and used along with some simplified test techniques to study the behavior of repaired concrete. Patched and nonpatched specimens are investigated under biaxial tension-compression states of stress. Different patch configurations, transition and rectangular, along with different patch depths are
openaire   +1 more source

Biaxial Fatigue Testing Of Vulcanizates

Rubber Chemistry and Technology, 1961
Abstract Extensive fatigue tests of vulcanizates of natural rubber and SBR were carried out using a cycle of alternate stretching in two perpendicular directions. It is shown that the data can be best handled statistically by assuming a lognormal distribution or by the use of extreme probability techniques.
S. D. Gehman, P. Rohall, D. I. Livingston   +2 more
openaire   +1 more source

Simulation of the scenario of the biaxial wheel fatigue test

Advances in Engineering Software, 2017
Abstract This paper presents a new approach to the virtualization of the scenario of the biaxial wheel fatigue test. This test is the state-of-art and the standard requirement for the validation of vehicle wheels. During this test, tire and wheel specimens run inside an inner drum while standardized vertical and horizontal loads are applied.
Fabio M. Santiciolli, Riccardo Möller, Ivo Krause, Franco Giuseppe Dedini   +3 more
openaire   +1 more source