Results 1 to 10 of about 70,429 (301)
Detection Method for Bolts with Mission Pins on Transmission Lines Based on DBSCAN-FPN
Zhongguo dianli, 2021 Bolts are the mostly used fasteners on transmission lines, and their defect detection is an important content for transmission line inspection. As the bolt with missing pins are small targets, their positioning is difficult and their features are hard to
Zhenbing ZHAO +3 more
doaj +1 more source
IET Networks, 2021 We consider leveraging the joint potential of non‐orthogonal multiple access (NOMA) and traffic offloading to benefit cell‐edge users in multi‐cell scenarios. We formulate the edge‐driven throughput maximisation problem where both the offloading decision
Yi Zhao, Di Yuan, Lei You
doaj +1 more source
A review of physical experimental research methods of mine bolt
Meikuang Anquan, 2023 Physical experiment is a commonly used research method in the field of modern natural science, but the experimental method in a single study is often limited, which cannot fully reflect the whole picture of the problem to be studied.
Xueling DU
doaj +1 more source
Avaria by the bottom of a bolt on a diesel of engine [PDF]
Journal of Research and Innovation for Sustainable Society, 2019 A drive from a diesel engine of a truck was broken into four parts during normal use. Damaged bolt caused longitudinal and transverse cracks. They started from the surface of the hole and stretched outward.
Negoita O. +8 more
doaj +1 more source
Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 2018 Civataüretiminin kritik prosesi olan ısıl işlem prosesi; soğuk şekillendirilenmalzemenin metalografik ve mekanik özelliklere olan etkisinin araştırılması,hem proses verimi hemde ürün performans kriterleri açısındandeğerlendirildiğinde sektörde deneysel ...
ALPER Baygut +2 more
doaj +1 more source
On Characteristics of a Bolted Joint with a Tap Bolt
TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C, 1981 The purpose of this paper is to examine a distribution of contact pressures on the interface of a cylindrical clamped part fastened with a tap bolt to a base which is sufficiently larger than the clamped part. The analysis is treated as a contact problem of two bodies.
SAWA, Toshiyuki +2 more
openaire +3 more sources
Preparation and Electrochemical Performance of a Honeycomb-like Porous Anode Material
International Journal of Electrochemical Science, 2017 Ground coffee is used to prepare a honeycomb-like porous anode material for Li-ion batteries. The microstructure and morphology of the as-prepared samples are characterized by X-ray diffraction and scanning electron microscopy.
Xin-xiu Li +4 more
doaj +1 more source
Influence Law of Foundation Pit Excavation on Stress of Surrounding Tunnel Bolt
Applied Sciences, 2022 Due to the existence of a tunnel next to the foundation pit, the soil surrounding the foundation pit deforms into the foundation pit due to the excavation unloading during the process of foundation pit excavation, which causes the deformation of the ...
Shengbin Hu +9 more
doaj +1 more source
Failure Analysis of High Strength Galvanized Bolts Used in Steel Towers
Metals, 2016 This paper analyses the failure of three bolts used in the structural connections of a number of steel towers located in northern Europe. The analysis comprises optical and scanning electron microscopy, microstructural and hardness analysis, mechanical ...
Jose Alberto Álvarez +4 more
doaj +1 more source
Study of the Load-Bearing Characteristics of Bolts under Asymmetric Freezing Conditions
Applied Sciences, 2023 To investigate the load-bearing characteristics of anchor rods under asymmetric freezing conditions such as those in cold regions and the effect of frost swelling, a model test device was developed using a controlled-temperature environmental box and a ...
Jie Dong +5 more
doaj +1 more source