Results 1 to 10 of about 215,222 (264)

Multi-scale characterization of bamboo bonding interfaces with phenol-formaldehyde resin of different molecular weight to study the bonding mechanism [PDF]

Journal of the Royal Society Interface, 2020
Yuxiang Huang, Qiuqin Lin, Yahui Zhang   +2 more
exaly   +2 more sources

Modeling of bonding pressure based on the plastic deformation mechanism of interfacial voids closure in solid-state diffusion bonding

Materials & Design
The model of the diffusion bonding pressure was established using the analysis calculation method and further verified by the finite element analysis (FEA) and the experiments.
Yu Peng, Jinglong Li, Zhaoxi Li, Zilong Guo, Wei Guo, Jiangtao Xiong   +5 more
doaj   +3 more sources

A preliminary study into the effect of oxide chemistry on the bonding mechanism of cold-sprayed titanium dioxide coatings on SUS316 stainless steel substrate

Journal of Electrochemical Science and Engineering, 2022
Current attention has focused on the preparation of thick ceramic coating of nano­structured materials as feedstock material using the thermal spray process.
Noor Irinah Binti Omar, Suhana Binti Mohamed, Yusliza Binti Yusuf, Toibah Binti Abdul Rahim, Zaleha Binti Mustafa, Syahriza Binti Ismail, Ilyani Akmar Binti Abu Bakar, Santirraprahkash Selvamani   +7 more
doaj   +1 more source

Langasite Bonding via High Temperature for Fabricating Sealed Microcavity of Pressure Sensors

Micromachines, 2022
We proposed a novel Langasite (LGS) bonding method only using high temperature to solve the manufacturing difficulty of the sealed microcavity of pressure sensors. The optimal bonding parameters by comparative experiments were defined as 1350 °C for 3 h.
Juan Zhang, Qiulin Tan, Lei Zhang, Nan Zhao, Xiaorui Liang   +4 more
doaj   +1 more source

Environment-friendly wood fibre composite with high bonding strength and water resistance [PDF]

Royal Society Open Science, 2018
With the growing depletion of wood-based materials and concerns over emissions of formaldehyde from traditional wood fibre composites, there is a desire for environment-friendly binders.
Xiaodi Ji, Yue Dong, Tat Thang Nguyen, Xueqi Chen, Minghui Guo   +4 more
doaj   +1 more source

Research Progress of Bonding Agents and Their Performance Evaluation Methods

Molecules, 2022
Bonding agents are an important type of additive that are used to increase the interfacial interaction in propellants. A suitable bonding agent can prevent the dewetting between the oxidant and binder, and thus effectively improve the mechanical ...
Junyan Gan, Xue Zhang, Wei Zhang, Rui Hang, Wuxi Xie, Yunfei Liu, Wen Luo, Yu Chen   +7 more
doaj   +1 more source

Mechanical Properties and Bonding Mechanism of the Mg/Al Clad Sheet Manufactured by the Corrugated Roll

Metals, 2023
In this research, corrugated Mg/Al clad sheet with good interface bonding was prepared with a rolling mill of upper corrugated roll and a lower flat roll under the conditions of 35% reduction and 400 °C.
Shi Zhao, Yaoqing Hu, Sha Li, Tao Wang
doaj   +1 more source

Oxide Free Wire Arc Sprayed Coatings—An Avenue to Enhanced Adhesive Tensile Strength

Metals, 2022
Conventionally, thermal spraying processes are almost exclusively carried out in an air atmosphere. This results in oxidation of the particles upon thermal spraying, and thus, the interfaces of the splats within the coating are oxidized as well. Hence, a
Manuel Rodriguez Diaz, Maik Szafarska, René Gustus, Kai Möhwald, Hans Jürgen Maier   +4 more
doaj   +1 more source

Influence of Cold Spray Parameters on Bonding Mechanisms: A Review

Metals, 2021
The cold spray process is governed by the impact of high velocity feedstock particles onto a substrate without melting. Hence, the bulk material properties are retained. However, it is challenging to achieve good adhesion strength.
Surinder Singh, R. K. Singh Raman, Christopher C. Berndt, Harpreet Singh   +3 more
doaj   +1 more source

Evaluation of the properties of plastic-metal interfaces directly bonded via injection molding

Manufacturing Review, 2020
Plastic and metal can be directly bonded via insert injection molding by creating surface porous structures with 30–50 nm sizes on metal surface. Molten polymers can be penetrated into the small pores created on metal surface in the short molding process,
Horiuchi Shin, Terasaki Nao, Itabashi Masami   +2 more
doaj   +1 more source