Results 61 to 70 of about 26,464 (267)

Is an Apple an Orange? A Large Language Model Benchmark for Candidate Term Extraction and Subclass Decisions Against Upper Ontologies in Engineering and Materials Science

Advanced Engineering Materials, EarlyView.
Building machine‐readable vocabularies for materials science is slow, expert‐driven work. This study benchmarks 13 large language models on two of its first steps: finding candidate terms in engineering articles and deciding where they belong in a class hierarchy.
Thomas Bjarsch, Maximilian Holland, Klaus Drechsler, Johannes Schilp   +3 more
wiley   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

Analysis of boundary layer flow over a porous nonlinearly stretching sheet with partial slip at

Alexandria Engineering Journal, 2013
The boundary layer flow of a viscous incompressible fluid toward a porous nonlinearly stretching sheet is considered in this analysis. Velocity slip is considered instead of no-slip condition at the boundary.
Swati Mukhopadhyay
doaj   +1 more source

Slip Localization Intensification Mediated by Grain Boundary Sliding in a Polycrystalline Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat, D. Anjaria, I. Woo, C. Bean, D. Texier, J. C. Stinville   +5 more
wiley   +1 more source

Estimating the slip rate in the North Tabriz Fault using focal mechanism data and GPS velocity field

Journal of Geodetic Science
This study delves into slip distribution on the North Tabriz Fault (NTF), a critical aspect of seismic hazard analysis due to its proximity to the Tabriz metropolis.
Salmanian Milad, Rastbood Asghar, Hossainali Masoud Mashhadi   +2 more
doaj   +1 more source

Magnetohydrodynamic (MHD) mixed convection slip flow and heat transfer over a vertical porous plate

Engineering Science and Technology, an International Journal, 2015
The effects of velocity slip and thermal slip on MHD boundary layer mixed convection flow and heat transfer of an incompressible fluid past a plate in presence of suction/blowing are presented.
Swati Mukhopadhyay, Iswar Chandra Mandal
doaj   +1 more source

Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales

Advanced Engineering Materials, EarlyView.
Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik, Alexander Jelinek, Markus Alfreider, Jutta Luksch, Anton Hohenwarter, Florian Schaefer, Christian Motz, Daniel Kiener   +7 more
wiley   +1 more source

Slip boundary conditions over curved surfaces

Physical Review E, 2016
Molecular dynamics simulations are used to investigate the influence of surface curvature on the slip boundary condition for a simple fluid. The slip length is measured for flows in planar and cylindrical geometries with a range of wall-fluid interactions.
Lin, Guo, Shiyi, Chen, Mark O, Robbins
openaire   +3 more sources

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source