Results 81 to 90 of about 26,464 (267)

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

II. On the alleged slipping at the boundary of a liquid in motion [PDF]

Proceedings of the Royal Society of London, 1890
Abstract The experiments of Helmholtz and Piotrowski on the oscillations of a metal sphere suspended bifilarly, and filled with various liquids, gave finite values to the slipping coefficients. The inside of the sphere was gilded and polished, and the value obtained for the coefficient λ was, in the case of distilled water, 2·3534 mm.
openaire   +1 more source

Modeling Dislocation Cutting of γ′ Precipitates in Ni‐Base Superalloys: Linking Atomistic and Dislocation Dynamics Simulations

Advanced Engineering Materials, EarlyView.
Dislocation cutting of γ′ precipitates in Ni‐based superalloys is investigated by linking atomistic simulations with discrete dislocation dynamics. The critical cutting stress is shown to be governed by the antiphase boundary energy, while line tension effects promote edge‐preferred cutting.
Frédéric Houllé, Siwen Gao, Marc Fivel, Anxin Ma, Daria Smirnova, Sriram Anand, Arun Prakash, Julien Guénolé, Alexander Hartmaier, Erik Bitzek   +9 more
wiley   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Non-Similar Computational Solution for Boundary Layer Flows of Non-Newtonian Fluid from an Inclined Plate with Thermal Slip

Journal of Applied Fluid Mechanics, 2016
The laminar boundary layer flow and heat transfer of Casson non-Newtonian fluid from an inclined (solar collector) plate in the presence of thermal and hydrodynamic slip conditions is analysed.
SUBBARAO ANNASAGARAM, V. Ramachandra Prasad, Nagendra N, N. Bhaskar Reddy, O. Anwar Beg   +4 more
doaj  

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source

Elastic Properties and Thermal Expansion Behavior of a Polycrystalline VMnFeCoNi High‐Entropy Alloy

Advanced Engineering Materials, EarlyView.
The high‐entropy alloy (HEA) V20Mn20Fe20Co20Ni20 (composition in at.%) can be made single‐phase face‐centered cubic (FCC) when annealed above 1338 K followed by water quenching. In this state, the alloy exhibits the greatest strength‐ductility combination of any quinary single‐phase FCC HEA.
Guillaume Laplanche, Marie Münchhalfen, Aditya Srinivasan Tirunilai, Jürgen Schreuer   +3 more
wiley   +1 more source

On the Effect of Creep on Local Lattice Orientation in Single‐Crystal Ni‐Based Superalloy Microstructures

Advanced Engineering Materials, EarlyView.
During creep of a single‐crystal Ni‐based superalloy, the overall crystal orientation is observed to remain constant while the microstructure evolves. Despite the lack of macroscopic rotation, small (<1°) rotations are observed on the submicron size scale and are accommodated by counteracting rotations over the scale of several micrometers.
E. J. Payton, E. B. Dursun, G. Eggeler, L. Agudo Jácome   +3 more
wiley   +1 more source

Distinct Microstructural Characteristic Lengths Defining Notch Fatigue Crack Initiation and Propagation, and Defect Tolerance in Advanced Steels

Advanced Engineering Materials, EarlyView.
Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley   +1 more source

Foundational Machine‐Learning Interatomic Potential for Simulating Chemically Complex Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
We apply a foundational machine‐learning interatomic potential based on the graph atomic cluster expansion (GRACE) to simulate the commercial Ni‐based single‐crystal superalloy CMSX‐4. Hybrid Monte‐Carlo/molecular dynamics sampling resolves short‐range order in the γ phase and L12 sublattice occupancies in the γ’ phase and connects them to stacking ...
Aditya Vishwakarma, Sarath Menon, Fritz Körmann, Thomas Hammerschmidt, Ralf Drautz   +4 more
wiley   +1 more source