Results 41 to 50 of about 226,851 (192)
Macromolecular Materials and Engineering, Volume 311, Issue 6, June 2026.Thermal analysis‐based (TGA/DTA) sintering provides a composition‐dependent route for optimizing Al‐graphene‐B4C hybrid composites. TGA/DTA identifies mass‐change intervals and suitable sintering temperature ranges, while XRD and SEM/EDX observations support phase and microstructural evaluation.
Gürkan Soy +3 more
wiley +1 more source
Effect of Cr2AlC content on the properties of a Cu-Cr2AlC composite
Results in Physics, 2016 A Cu-Cr2AlC composite material is prepared by low-temperature hot-press sintering and the electrical properties of the composite material are discussed in this paper.
Xin-sheng Wang +4 more
doaj +1 more source
Hardness relationship between eNM3A10 and conventional hardness scales
Measurement: Sensors, 2021 Small ball rebound hardness eNM3A10 is a next-generation rebound hardness test with features not existing in conventional rebound hardness tests: reduced mass effect of hardness and satisfying the similarity rule of hardness (Minimum thickness of steel ...
Takashi Yamamoto +2 more
doaj +1 more source
steel research international, Volume 97, Issue 6, Page 3308-3327, June 2026.The effect of chemical inhomogeneity on the microstructure and properties of nanobainitic steel is investigated. A two‐stage isothermal heat treatment that produced a more uniform microstructure is designed. The first‐stage temperature is higher than the MS of depleted bands; conversely, the second‐stage temperature is lower than the first‐stage ...
Bogdan Garbarz +5 more
wiley +1 more source
Toughening β‐Ga2O3 via Mechanically Seeded Dislocations
Advanced Functional Materials, Volume 36, Issue 30, 13 April 2026.β‐Ga2O3 is promising for next‐generation semiconductors but its brittleness limits flexible and high‐precision applications. Here, mechanically seeded dislocations introduced by surface deformation improved damage tolerance in (001) β‐Ga2O3. Nanoindentation and characterization show dislocations suppress cleavage cracks by enabling stable plastic ...
Zanlin Cheng +5 more
wiley +1 more source
مجلة بغداد للعلوم, 2020 : In this study a type of polymeric composites from melting poly propylene as a basic substance with Palm fronds powder were prepared.
Ebtehag Sulyman, Noaman Sulyman
doaj +1 more source
Advanced Engineering Materials, Volume 28, Issue 6, 18 March 2026.This work presents a simulation‐based framework based on representative volume elements (RVEs) that explicitly incorporates process‐induced second‐order residual stresses into the fatigue strength assessment of ductile cast iron (DCI). For the first time, this approach enables a direct evaluation of the influence of second‐order residual stress fields ...
Lutz Horbach +4 more
wiley +1 more source
RETRACTED: Indentation parameters for Brinell hardness measurement of low carbon steels [PDF]
E3S Web of ConferencesSee the retraction notice E3S Web of Conferences 549, 00001 (2024), https://doi.org/10.1051/e3sconf ...
Udalov A.V., Udalov A.A., Norin E.G.
doaj +1 more source
Robust Smart Superhydrophobic Cilia
Advanced Science, Volume 13, Issue 12, 27 February 2026.To date, ciliated surfaces cannot withstand mechanical damage because cilia/wires are inherently fragile. By aligning magneto‐responsive, flexible, superhydrophobic microwires on the sidewall of vertical frames, the frames act as armors to protect microwires from mechanical damage; when needed, the microwires re‐align uprightly under a magnet field to ...
Chuanqi Wei +4 more
wiley +1 more source
Media MesinDue to advancements in the industrial sector, aluminum is progressively gaining popularity as a material of choice in the field of engineering. A pulley is a component that functions as a link or transfers power or engine rotation to the load via the V ...
Andika Wisnujati, Muhammad Abdus Shomad
doaj +1 more source