Results 181 to 190 of about 616,215 (256)

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

CCH-Pd complex anchored on ZrFe₂O₄ nanoparticles as a novel magnetic catalytic for C-C coupling reactions. [PDF]

Heliyon
Sdiq ZM, Pourmokhtar H, Keshavarzi F.
europepmc   +1 more source

Facilitating Expedited Drug Approval—the Past, Present, and Future of Clinical Trials for Pediatric Rheumatic Disease

Arthritis Care &Research, EarlyView.
Pamela F. Weiss, Hermine I. Brunner
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Manipulating C-C coupling pathway in electrochemical CO₂ reduction for selective ethylene and ethanol production over single-atom alloy catalyst. [PDF]

Nat Commun
Wang S, Li F, Zhao J, Zeng Y, Li Y, Lin ZY, Lee TJ, Liu S, Ren X, Wang W, Chen Y, Hung SF, Lu YR, Cui Y, Yang X, Li X, Huang Y, Liu B.   +17 more
europepmc   +1 more source

Variable Stiffness Flexure Structures Enabled by Phase‐Change Gallium and Adhesive Interfacial Locking for Soft Robotic Applications

Advanced Engineering Materials, EarlyView.
A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim, Sohee John Yoon, Yong‐Lae Park   +2 more
wiley   +1 more source

Cu supraparticles with enhanced mass transfer and abundant C-C coupling sites achieving ampere-level CO₂-to-C₂₊ electrosynthesis. [PDF]

Nat Commun
Ma L, Liu H, Mei B, Chen J, Cheng Q, Ma J, Yang B, Li Q, Yang H.   +8 more
europepmc   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

2D Undulated Metal Hydrogen-Bonded Organic Frameworks with Self-Adaption Interlayered Sites for Highly Efficient C-C Coupling in the Electrocatalytic CO₂ Reduction. [PDF]

Nanomicro Lett
Lv J, Li W, Li S, Xu S, Lv Z, Zhu Z, Dai L, Wang B, Li P.   +8 more
europepmc   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source