Results 31 to 40 of about 997 (171)
Materials Genome Engineering Advances, EarlyView.Four constitutive models are evaluated for FeCoNiCr and Al0.6FeCoNiCr HEAs under wide temperature and strain‐rate conditions. The predictive capabilities and limitations of each model are then critically assessed, with particular emphasis on strain rate sensitivity, temperature dependence, and physically unrealistic responses at extreme loading ...
Yooseob Song +3 more
wiley +1 more source
THE FORMATION OF ANTI-CORROSIVE STRUCTURES AND THIN FILMS ON METAL SURFACES BY APPLYING EDM [PDF]
Journal of Engineering Science (Chişinău), 2018 The methods of formation anti-corrosive strata and thin films on metal surfaces by applying electric discharge machining (EDM) are presented in this chapter. It has been demonstrated the increase of anti-corrosion resistance of metal surfaces
Pavel Topala +3 more
doaj +1 more source
Pediatric Investigation, EarlyView.Children with cancer received more palliative care consultation before, but fewer during, critical illness compared with adults. This disparity suggests underuse of palliative care during pediatric critical care. ABSTRACT Importance Palliative care consultation is an essential component of comprehensive care for patients with cancer during critical ...
Conrad Krawiec, Neal Thomas
wiley +1 more source
International Journal of Electrochemical Science, 2019 The effect of heat treatment on corrosion of C45 mild steel coated with WC-Co-Al2O3 cermet composite were examined. The cermet coatings (CC) were produced by electrospark deposition (ESD) technology.
Mieczyslaw Scendo, Klaudia Szczerba
doaj +1 more source
Durability performance of a high‐performance fiber‐reinforced concrete for bridge applications
Structural Concrete, EarlyView.Abstract This paper investigates the durability performance of a coarse‐aggregate high‐performance fiber‐reinforced concrete (HPFRC) developed as a cost‐efficient material solution for precast bridge applications. A comprehensive experimental program was conducted to assess the resistance of the material to the principal deterioration mechanisms ...
Rolando Baldiviezo +6 more
wiley +1 more source
Rapid Determination of the S-N Curve for Steel by means of the Thermographic Method
Advances in Materials Science and Engineering, 2016 The paper presents a thermographic method of accelerated determination of the S-N curve. In the presented method, the S-N curve was developed based on energy-related parameter with the assumption of its dependency on the stress amplitude.
Adam Lipski
doaj +1 more source
Structural Concrete, EarlyView.Abstract Ground granulated blast‐furnace slag (GGBS) is a widely used clinker substitute in concrete, recognized for its potential to significantly reduce environmental impacts. However, its application in prestressed concrete remains limited in several countries, mainly due to concerns regarding early‐age mechanical performance and long‐term ...
D. Rolando Baldiviezo +6 more
wiley +1 more source
Modelling and Multi-objective Optimization of Elastic Abrasive Cutting of C45 and 42Cr4 Steels
Strojniški vestnik – Journal of Mechanical Engineering, 2021 Elastic abrasive cutting is a new high-performance method to produce workpieces made of materials of different hardness, which ensures lower wear of cut-off wheels and higher quality machined surfaces. However, the literature referring to elastic abrasive cutting is scarce; additional studies are thus needed.
Stefanova Aleksandrova, Irina +2 more
openaire +2 more sources
Effect of Overlap Length on the Strength of Adhesive Joints of Steel Sheets
Technologia i Automatyzacja Montażu, 2022 The study evaluates the shear strength of the single-lap adhesive joints made of C45 carbon steel. The influence of the overlap length on the shear strength of the adhesive joint was tested. The elongation of the samples was also tested.
Elżbieta Doluk +3 more
doaj +1 more source
Governance, Volume 39, Issue 4, October 2026.ABSTRACT Public service co‐production is often framed as a means of creating public value, yet its dynamics are complex when citizen‐led participation is catalyzed by strong public institutions. This mixed‐methods study examines government‐catalyzed, citizen‐centric co‐production in Shanghai, China, where the state provides institutional support ...
Huanming Wang, Xiaoyun Sun, Bing Ran
wiley +1 more source