Results 121 to 130 of about 36,273 (305)

Van der Waals Chromium Telluride Thin Films Prepared by Hybrid Pulsed Laser Deposition With Tunable Magnetism

Advanced Materials Interfaces, EarlyView.
Epitaxial Cr(1+δ)Te2 thin films were synthesized via hybrid Pulsed Laser Deposition (PLD) that combined Molecular Beam Epitaxy (MBE) techniques with PLD. Control of the Cr intercalation, δ, enabled modulation of magnetic anisotropy, Curie temperature, and transport properties.
Pia Henning, Anna Tschesche, Tobias Meyer, Jasnamol Palakkal   +3 more
wiley   +1 more source

Parallel Electrical Integration of Photo Bio Electrochemical Systems (photo‐BESs): Performance Gains and Load Dependency

Advanced Materials Technologies, EarlyView.
Parallel wiring of bioelectrochemical devices with conventional generators unexpectedly boosts output. A biophotovoltaic paired with a solar cell delivers up to 50% more power at low loads than their separate contributions; a plant microbial fuel cell shows similar current gains.
Valeria Marsaglia, Paolo Bombelli, Ingrid Paoletti, Ioannis A. Ieropoulos, Christopher J. Howe   +4 more
wiley   +1 more source

Determination of metronidazole on modified carbon paste electrode [PDF]

, 2013
This bachelor thesis examines the possibilities of suppression of the oxygen signal of carbon paste electrode by modification of the electrode with a reductant. Two modifiers were chosen: sodium sulphite and sodium hypophosphite.
Axmannová, Hana
core  

Overcoming Printing and Interfacial Challenges in Liquid Metal Direct Writing for Integrated Stretchable Electronics

Advanced Materials Technologies, EarlyView.
Liquid metal direct writing is advanced from a technological and fundamental point. Utilizing a kinematic bed, printing on large surfaces with irregularities is enabled. Furthermore, a pressure‐driven flow during printing is discovered that affects the thickness of traces.
Maximilian Krack, Lennert Purnal, Parth Vinayakrao Sewlikar, Sam Cuyvers, Gus Geurts, Rathul Nengminza Sangma, Derese Desta, Dieter Reenaers, Bart Ruttens, Iris De Graeve, Tom Hauffman, Seppe Terryn, Bram Vanderborght, Michaël Daenen, Wim Deferme, Monika Rai   +15 more
wiley   +1 more source

Smart and Sustainable Sizing: Investigating the Sensing Behavior of Glass Fabrics Coated With Waterborne Polyurethane/Graphene Dispersions

Advanced Materials Technologies, EarlyView.
Waterborne polyurethane/graphene formulations are developed as piezoresistive coatings on glass fabric to enable flexible strain sensing. The graphene‐enabled conductive network provides a stable electromechanical response under cyclic compression. The coating demonstrates reliable pressure‐dependent resistance changes, highlighting its potential for ...
Vishnu Vijayan Pillai, Premika Govindaraj, Sai Aditya Pradeep, Olivia Sequerth, Srikanth Pilla, Franz Konstantin Fuss, Peter Kingshott, Nishar Hameed, Nisa V Salim   +8 more
wiley   +1 more source

End‐to‐End Sensing Systems for Breast Cancer: From Wearables for Early Detection to Lab‐Based Diagnosis Chips

Advanced Materials Technologies, EarlyView.
This review explores advances in wearable and lab‐on‐chip technologies for breast cancer detection. Covering tactile, thermal, ultrasound, microwave, electrical impedance tomography, electrochemical, microelectromechanical, and optical systems, it highlights innovations in flexible electronics, nanomaterials, and machine learning.
Neshika Wijewardhane, Lyn I. Jones, Richard M. Martin, Helen Winter, Faezeh Arab Hassani   +4 more
wiley   +1 more source

Mechanical Fatigue in Liquid‐Metal Interconnects: Failure Mechanism Analysis and Validation of Improvement Strategies

Advanced Materials Technologies, EarlyView.
Multi‐million cycle reliability for liquid metal stretchable electronics is achieved through a continuous cycle of mechanical testing, failure mode and mechanism analysis and implementing subsequent mitigation strategies. ABSTRACT Stretchable electronics that combine mechanical compliance with reliable electrical performance are essential for ...
Lennert Purnal, Maximilian Krack, Parth Vinayakrao Sewlikar, Bart Ruttens, Tom Hauffman, Iris De Graeve, Wim Deferme, Michaël Daenen, Monika Rai   +8 more
wiley   +1 more source

Additive‐Manufactured, Multifunctional Bioreactor Technology for Dynamic Culture of 3D Bioprinted Tissue Models

Advanced Materials Technologies, EarlyView.
We introduce an additively manufactured bioreactor with a perfusion flow system and integrated temperature and pH sensors for skeletal muscle tissue biofabrication. The bioreactor's performance was evaluated by assessing the viability, spreading of the myoblast cells in a printed scaffold, and contraction of the isolated murine musculi interossei ...
Lys Sprenger, Johann Schorzmann, Hsuan‐Heng Lu, Muhammad Osama, Julian Bauer, Michael Haug, Oliver Friedrich, Aldo R. Boccaccini, Frank Döpper, Sahar Salehi   +9 more
wiley   +1 more source

4. CARBON PASTE AS A SUPPORT FOR METALLIC FILM ELECTRODES

, 2009
: An overview is given dealing with the applications of carbon paste electrodes in equilibrium potentiometry as well as in electrochemical stripping analysis using both voltammetric and potentiometric modes.
Ivan Švancara, Karel Vytřas, Radovan Metelka   +2 more
core  

Single-wall carbon nanotube paste electrodes: a comparison with carbon paste, platinum and glassy carbon electrodes via cyclic voltammetric data

, 2004
A new carbon electrode material, obtained by mixing single wall carbon nanotubes (SWNTs) with a mineral oil binder is studied. Carbon nanotube pastes show the special properties of carbon nanotubes combined with the various advantages of composite ...
Irma Lavagnini, Giuseppe Palleschi, Federica Valentini, ANTIOCHIA, RICCARDA, Franco Magno   +4 more
core   +1 more source