Results 41 to 50 of about 2,160,942 (204)

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring

Advanced Engineering Materials, EarlyView.
Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak, Yasmina Frey, Ulrike Wallrabe, Oswald Prucker, Jürgen Rühe   +4 more
wiley   +1 more source

Study on Mechanism of Chemical Sulfate Attack on Reinforced Concrete Structures

Chemical Engineering Transactions, 2017
This paper studies four different cementitious materials including ordinary Portland cement paste and cement fly ash in closed environment based on previous study on characteristics of carbon sulphosilicate formation in single sulfate solution.
Liyuan Xie, Gang Wang
doaj   +1 more source

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

A Modified Ho3+ Carbon Paste Electrode Based on Multi-walled Carbon Nanotubes (MWCNTs) and Nanosilica

International Journal of Electrochemical Science, 2009
A novel carbon paste ion selective electrode for determination of trace amount of holmium was prepared. Multi-walled carbon nanotubes (MWCNTs) and nanosilica were used for improvement of a holmium carbon paste sensor response.
Mohammad Reza Ganjali, Negar Motakef-Kazemi, Parviz Norouzi, Sepideh Khoee   +3 more
doaj   +1 more source

Effect of Ultrafine Additives on the Morphology of Cement Hydration Products

Crystals, 2021
The present research is focused on the investigation of the influence of ultrafine additives on the structure formation of hardened cement paste and the establishment of the mechanisms of the morphological transformations, which determine the properties ...
Grigory Yakovlev, Rostislav Drochytka, Gintautas Skripkiūnas, Larisa Urkhanova, Irina Polyanskikh, Igor Pudov, Ekaterina Karpova, Zarina Saidova, Ali E. M. M. Elrefai   +8 more
doaj   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Microstructural Evolution and In Situ Formation of TiB and TiC in Ti─5Al─2.5Sn Alloy Processed by Powder Metallurgy

Advanced Engineering Materials, EarlyView.
Accelerated in situ formation of TiB and TiC in Ti–5Al–2.5Sn–B4C is driven by transient liquid phase formation, which enhances particle reactions and microstructural evolution. This process increases hardness and establishes a coupled relationship between sintering temperature and reinforcement content, strongly influencing porosity in the resulting ...
Fernando. Y. Kojima, Juliano. Soyama
wiley   +1 more source

Enhancing Low‐Temperature Performance of Sodium‐Ion Batteries via Anion‐Solvent Interactions

Advanced Functional Materials, EarlyView.
DOL is introduced into electrolytes as a co‐solvent, increasing slat solubility, ion conductivity, and the de‐solvent process, and forming an anion‐rich solvent shell due to its high interaction with anion. With the above virtues, the batteries using this electrolyte exhibit excellent cycling stability at low temperatures. Abstract Sodium‐ion batteries
Cheng Zheng, Qian Yao, Yanan Sun, Hongyu Lv, Zhongchao Bai, Guoliang Zhang, Nana Wang, Jian Yang   +7 more
wiley   +1 more source

Manufacturing a Modified Carbon Paste Electrode with Catalase Enzyme-Au Nanoparticles for Electrochemical Sensing of Hydrogen Peroxide and Their Electrocatalytic Properties

International Journal of Electrochemical Science, 2014
To find hydrogen peroxide, different techniques applied, recently. In this practice we decided to produce a modified carbon paste electrode by catalase enzyme-Au nanoparticles for electrochemical sensing hydrogen peroxide and their electroactivity ...
Parisa Sistani, Akram Noori, Masoomeh Fathollahi Motlagh, Amir Habibi Tamijani, Elahe Imani, Yeganeh Shadram, Roya Rahimzadeh, Behnam Ebrahimi, Mohammadtaghi Sarebanhassanabadi, Masoud Negahdary, Sahar Majdi   +10 more
doaj   +1 more source