Results 11 to 20 of about 2,252,051 (238)
Sustainable design and durability of domestic micro combined heat and power scroll expander systems. [PDF]
Research to understand the mechanisms of wear within the main components of three different micro-CHP scroll expander systems was conducted. This was performed in order to identify the possible tribo-mechanical effects (abrasion, adhesion, cavitation ...
Tzanakis, Iakovos
core +9 more sources
Cavitation analysis of a double acting podded drive during ice milling [PDF]
, 2009 Propeller ice interaction is a complex phenomenon, which relies on innovative and complex experimental research in dedicated ice tank facilities. Whilst the ice tanks model the contact forces with good agreement, the hydrodynamic loading is often only ...
Atalr, M., Sasaki, N., Sampson, Roderick
core +7 more sources
Analysis of Cavitation Instabilities in a Four-Blade Inducer [PDF]
, 2012 The cavitating behavior of a four-blade inducer tested in the LML laboratory large test facility is considered in the present paper. Experimental investigations based on unsteady pressure measurements and records from a six-component balance mounted on ...
DAZIN, Antoine +7 more
core +1 more source
Xibei Gongye Daxue Xuebao, 2021 In order to study the influence of the ventilating cavitation flow at the shoulder of a submerged-launched vehicle on the surface hydrodynamic characteristics, a three-dimensional potential model for the shoulder ventilation of the vehicle was ...
doaj +1 more source
Early Stage Cavitation Erosion within Ceramics: An Experimental Investigation [PDF]
, 2009 Six ceramic material types were considered within an experimental investigation to identify the erosion damages mechanisms resulting from cavitation exposure.
Hadfield, M. +6 more
core +1 more source
Cavity induced vibration of flexible hydrofoils [PDF]
, 2014 The objective of this work is to investigate the influence of cavity-induced vibrations on the dynamic response and stability of a NACA66 hydrofoil at 8° angle of attack at Re=750 000 via combined experimental measurements and numerical simulations.
CHAE, Eun Jung +4 more
core +1 more source
Cavitation wear of Eurofer 97, Cr18Ni10Ti and 42HNM alloys
Acta Polytechnica, 2021 The microstructure, hardness and cavitation wear of Eurofer 97, Cr18Ni10Ti and 42HNM have been investigated. It was revealed that the cavitation resistance of the 42HNM alloy is by an order of magnitude higher than that of the Cr18Ni10Ti steel and 16 ...
Hanna Rostova +7 more
doaj +1 more source
Effect of section thickness on cavitation behaviour of selective laser sintered polyamide 12 [PDF]
Science of SinteringThe present study focuses on the results of cavitation resistance of samples obtained by the Selective Laser Sintering technology. All samples are made from Nylon 12 – Polyamide 12 powder, known as PA2200 in the industry, produced by EOS GmbH. The powder,
Dojčinović Marina B. +4 more
doaj +1 more source
An experimental analysis of fluid structure interaction on a flexible hydrofoil in various flow regimes including cavitating flow [PDF]
, 2012 The authors gratefully acknowledge the technical staff of IRENav for its contribution to the experimental set up.The structural response of a rectangular cantilevered flexible hydrofoil submitted to various flow regimes is analyzed through an original ...
SIGRIST, Jean-François +2 more
core +1 more source
Cavitation erosion of samples based on cordierite-talc ceramics [PDF]
Science of SinteringIn the paper, the cavitation resistance of cordierite samples with the addition of 10%, 15% and 20% talc, sintered at 1200⁰ C, was investigated. The ultrasonic vibration method with a stationary sample according to the ASTM G32 standard was applied.
Pavlović Marko +6 more
doaj +1 more source