Results 11 to 20 of about 22,242 (292)
Bonding Properties of TiAlCrSiN Coating / WC-8Co Cemented Carbide with Microtextured Surface [PDF]
Archives of Metallurgy and Materials, 2023 WC-8Co cemented carbide was prepared by a high-temperature liquid phase sintering in argon at 5-200 Pa. Three microtextured grooves with a spacing of 500, 750, and 1000 μm were prepared on the surface of WC-8Co cemented carbide.
ManFeng Gong +7 more
doaj +1 more source
Materials Research Express, 2021 Gasping the thermodynamic and phase diagram of the materials being studied is essential for further guiding the development process, like composition design, heat treatment optimization and so on.
Yingbiao Peng +6 more
doaj +1 more source
Fabrication and Tribology Properties of Cr-Coated Cemented Carbide under Dry Friction Conditions
Lubricants, 2023 To improve the surface friction characteristics of cemented carbide, a Cr coating was deposited on cemented carbide substrate with the multiple arc plating technique.
Li Zhang +5 more
doaj +1 more source
Crystals, 2021 Currently, the research on mechanical behavior and cutting performance of functionally graded carbides is quite limited, which limits the rapid development of high-performance cemented carbide cutting tools.
Shidi Li +9 more
doaj +1 more source
Research Progress in Cemented Carbide with Co-Ni-Al Composite Binder Phase
Journal of Aeronautical Materials, 2018 The application background of Co-Ni-Al composite binder phase in cemented carbide was introduced. The latest research results of Co-based superalloy and the properties of cemented carbide with binder strengthened by ordered phase were briefly described ...
LONG Jianzhan +6 more
doaj +1 more source
A new method for preparation of tungsten carbide powder by in situ electrochemical reduction
Electrochemistry Communications, 2022 A new electrochemical method for efficient and green recovery of cemented carbide in a molten salt is described. Tungsten powder is the main product when recovering cemented carbide by molten salt electrolysis.
Liwen Zhang, Xiaoli Xi, Zuoren Nie
doaj +1 more source
Laser surface texturing of a WC-CoNi cemented carbide grade: surface topography design for honing application [PDF]
, 2018 Abrasive effectiveness of composite-like honing stones is related to the intrinsic surface topography resulting from the cubic boron nitride (CBN) grains protruding out of the metallic matrix.
Bähre, Dirk +2 more
core +2 more sources
Study on Friction and Wear Characteristics of Coating on Surface of WC Cemented Carbide and Its Milling Performance [PDF]
Cailiao Baohu, 2023 In order to investigate the friction and wear characteristics of nitride coatings on surface of WC cemented carbide and their effect on tool milling performance, TiN, CrN and TiAlN nitride coatings were deposited on surface of WC cemented carbide by ...
SHAO Shu-feng, CHENG Xian-ming, SUN Shou-Yu, YANG Ke, FENG Yuan
doaj +1 more source
On Measurement and Interpretation of Toughness Behaviour of Carbide Tools [PDF]
, 1981 The actual significance of any definition of toughness behaviour of carbide tools depends on the existence of an interrelation between the quality as defined and the occurrence of chipping and premature failure in cutting.
Kals, H.J.J.
core +2 more sources
Cailiao gongcheng, 2016 A series of WC-1.0TiC-3.1TaC-4.5Co cemented carbides were prepared by vacuum sintering and Sintering-HIP through traditional powder metallurgy method. Optical microscopy(OM),scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS)
LI Zhong-dian +5 more
doaj +1 more source