Results 11 to 20 of about 14,821 (161)
A Novel Metal Foam-Supported Solid Oxide Fuel Cell With High Specific Power. [PDF]
Adv Sci (Weinh)Solid oxide fuel cells (SOFCs) employing metal foam supports with an ultrahigh porosity of 90% and average pore size of 100 µm are successfully fabricated. The metal foam architecture significantly enhances gas diffusion coefficients, effectively reducing concentration polarization while simultaneously decreasing areal mass.
Ma J, Yang Y, Ni M, Zhang Y, Yan M.
europepmc +2 more sources
Journal of Materials Research and Technology, 2022 In this study, “Z-pins like” M-MC1-x (M = Zr, Hf) gradient cermet rods were prepared by the carbon diffusion in situ reaction method, and the effects of different heat treatment temperatures on the microstructure of MC layers in “Z-pins like” M-MC1-x ...
Xin Qing +4 more
doaj +1 more source
A Fuzzy Evaluation of Tool Materials in the Turning of Marine Steels
Metals, 2021 To recommend one suitable tool material for the cutting of marine steels under special conditions and requirements in emergency rescues of capsized steel ships, the cermet tools, cemented carbide tools and coated carbide tools were evaluated using a ...
Qingzhong Xu +4 more
doaj +1 more source
Mitigation of corrosion attack on carbon steel coated cermet alloy in different anion contents [PDF]
, 2017 This research study evaluated the corrosion mechanism attack on carbon steel coated with cermet alloys (WC9% Ni) in seawater at different sulphate-to-chloride ratios.
Ismail, Azzura +1 more
core +2 more sources
The effect of roller pressure and feed rate on hides squeezing [PDF]
E3S Web of Conferences, 2023 The article presents the results of experimental studies of the process of extracting excess liquid from a water-saturated hide. The experiments were conducted in two options: using a rigid base plate and a cermet base plate for the feed mechanism of the
Bahadirov Gayrat +2 more
doaj +1 more source
Comparative Analysis on Reinforcement of Potential Additives in WOKA Cermet HVOF Coating Subjected to Slurry Erosion in Ash Conditions [PDF]
Iranian Journal of Materials Science and Engineering, 2022 In this paper, an investigation was carried out to test the suitability of potential additive materials in WOKA 3533 (WC-10Co4Cr) cermet HVOF coating subjected to slurry erosion in ash conditions.
Jashanpreet Singh +3 more
doaj
Journal of Materiomics, 2021 Metallic nanoparticle (NP)/ceramic composite cermets present desirable broadband absorption of the solar spectrum and thus are the preferred material scheme for constructing cermet-based solar absorbers.
Xiaoyu Wang +7 more
doaj +1 more source
Crystals, 2021 Two-dimensional (2D) electron back scattered diffraction (EBSD) is a powerful tool for microstructural characterization of crystalline materials. EBSD enables visualization and quantification of the effect of synthesis methods on the microstructure of ...
Muhammed Ali Shaikh Abdul +5 more
doaj +1 more source
LiCo Dual-Doped Ceria-Based Composite as a Promising Low-Temperature Electrolyte for Metal-Supported Solid Oxide Electrolyzers. [PDF]
ChemSusChemEnhanced sinterability and ionic conductivity are achieved with Li and Co dual‐doped GDC electrolytes for metal‐supported solid oxide electrolyzers. The optimized sample shows 2.17 × 102 S cm1 at 750 °C, which typically approaches the superionic solid electrolyte conductivity ranges. A tubular cell fabrication and analysis demonstrated its potential as
Liu Y +4 more
europepmc +2 more sources
Journal of Materials Research and Technology, 2021 The objective of the present work was to investigate the effect of different cermet coatings on tensile and high-cycle fatigue properties of AISI 1045 steel using High-Velocity Oxygen Fuel (HVOF) thermal spray process. In this study, the WC-12Co, WC-10Co-
Gi-Su Ham +4 more
doaj +1 more source