Results 21 to 30 of about 1,533,791 (361)
High index top layer for multimaterial coatings [PDF]
, 2016 For application in future cryogenically cooled gravitational wave detectors, the thermal noise of low absorbing mirror coatings has to be reduced. The development of low mechanical and optical loss materials is challenging, but thermal noise reduction ...
Martin, Iain W., Steinlechner, Jessica
core +1 more source
Physical and Tribological Properties of Nitrided AISI 316 Stainless Steel Balls
MATEC Web of Conferences, 2016 AISI 316 austenitic stainless steel balls (diameters 5.0 and 12.0 mm, typical hardness 250 HV0.3) and flat samples (20×20×2.0 mm) were nitrided by a pulsed glow discharge Ar/N2 plasma. Hardness of the ball surfaces was analysed using Vickers indentation.
Yang Shicai +4 more
doaj +1 more source
Polymer Testing, 2022 Development of bio-based vitrimers attracted significant attention due to these species’ excellent recyclability and renewability. However, most bio-based vitrimers require high-temperature curation and catalyst use.
Min Liu +8 more
doaj +1 more source
Towards a new method for coating heritage lead [PDF]
, 2014 Ethanolic solutions of long-chain carboxylic acids can be applied to lead metal substrates to form a coating of lead carboxylate which provides protection against atmospheric pollutants.
Adriaens, Mieke +5 more
core +2 more sources
Advances in Materials Science and Engineering, 2012 Methyltrimethoxysilane has been used as a base in the formation of transparent sol-gel coatings on glass substrates. Several types of alcohol were used as solvents in order to obtain the highest transparency and scratch hardness of the film.
W. Ahliah Ismail +2 more
doaj +1 more source
UV-Cured Antibacterial Hydrogels Based on PEG and Monodisperse Heterofunctional Bis-MPA Dendrimers
Molecules, 2021 Bacterial infections are one of the major threats to human health due to the raising crisis of antibiotic resistance. Herein, second generation antibacterial heterofunctional dendrimers based on 2,2-bis(methylol)propionic acid were synthesized.
Patrik Stenström +5 more
doaj +1 more source
Sliding wear of a-C:H coatings against alumina in corrosive media [PDF]
, 2013 This paper reports the results obtained from the study of friction and sliding wear in two corrosive solutions of an a-C:H coating deposited on 316L stainless against an alumina ball, employed as static counter part. Calculations of the values of the von
CARRASQUERO, E. +7 more
core +7 more sources
Friction of Teflon-S-coated Ti-6Al-4V under conditions of oscillatory relative motion [PDF]
, 1990 An extendable prosthesis for implantation in a human leg has been developed. The friction forces during extension of the prosthesis must be low, so a coating of Teflon-S was applied to the sliding surfaces. During walking, damage can occur as a result of
Gee, A.W.J. de +2 more
core +4 more sources
Accelerated thermal profiling of gas turbine components using luminescent thermal history paints
Journal of the Global Power and Propulsion Society, 2018 Introduction Methodology Results and discussion Conclusions Competing interests Funding sources References OPEN ACCESS PEER REVIEWED Accelerated thermal profiling of gas turbine components using luminescent thermal history paints Silvia ...
Silvia Araguás Rodríguez +7 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 Solid and liquid oxidation products have been considered to be the key issues to influence the ablation resistance of UHTCs coatings. However, the effect of solid oxidation products on the ablation performance is not clear.
Yixiang Xu +6 more
doaj +1 more source