Results 111 to 120 of about 12,584,658 (247)
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys
Advanced Engineering Materials, EarlyView.An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi +5 more
wiley +1 more source
Single point incremental forming of cold-rolled polycarbonate sheets
, 2019 The present work aims to examine the influence of a preliminary cold-rolling of polycarbonate sheets on the single point incremental forming of this outstanding engineering material.
Langella, A. +9 more
core +1 more source
A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation
Advanced Engineering Materials, EarlyView.A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler +4 more
wiley +1 more source
Effects of Mg on Microstructure and Solidification of a Hypereutectic Zn–8 wt.%Al Alloy
Advanced Engineering Materials, EarlyView.An appreciable set of results involving thermal data, microstructure, chemical composition, and microstructural growth laws is reported for ZnAlMg alloys. Such results demonstrate that ZnAlMg alloys have high potential for applications in automotive self‐lubricating components, batteries, and electrical systems.
Raí B. de Sousa +6 more
wiley +1 more source
PRODUCTION OF CASTINGS WITHOUT PINHOLE POROSITY
Литьë и металлургия, 2005 The article is dedicated to pinhole porosity forming in castings at using of the slugs received under Cold-box-amin-process. The mechanism of pinhole porosity forming is revealed, new criteria of its prevention are established, recommendations on its ...
A. N. Boldin, D. A. Soljakov
doaj
Advanced Engineering Materials, EarlyView.Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.PUF/ENB microcapsules were synthesized based on a sequential factorial design and incorporated into an epoxy matrix. Their anticorrosive action, associated with the self‐healing mechanism, demonstrated that the addition of microcapsules to the coating improved anticorrosive performance compared to pure epoxy coatings, particularly when the encapsulate ...
Vandicleya Alves Moreira +6 more
wiley +1 more source
The Effect of Cold Forming on Type 3CR12 Square Tubes [PDF]
, 1998 A non linear finite element simulation is conducted which completely simulates the forming of the tube from flat virgin plate to its final shape. The predicted residual stresses and amount of cold forming in the tube sides and comers are then compared ...
Laubscher, Rudolph
core +1 more source