Results 41 to 50 of about 1,480,294 (293)
COMPETITION ASPECTS IN THE AI ACT – NAVIGATING THE MURKY WATERS OF THE ABUSIVE PRACTICES IN A DECENTRALISED VIRTUAL WORLD [PDF]
The whole European construction, based on the three initial European Communities (namely, the European Coal and Steel Community, the European Economic Community and the European Atomic Energy Community) were built with several goals in mind, one of ...
Iulian BĂICULESCU
doaj
DEVELOPMENT AND GOALS OF COMPETITION LAW
The article presents the historical development of competition law discussing reasons for adopting particular national antimonopoly legislation. The following analysis of goals of competition law leads to the conclusion that there is no agreement what ...
Mateusz Błachucki
doaj +1 more source
Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones
A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell +3 more
wiley +1 more source
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Meningkatnya kesadaran akan pentingnya persaingan usaha menimbulkan munculnya regulasi tertentu di tingkat nasional dan hal inilah yang terjadi di Malaysia, yakni dengan berlakunya Undang-Undang Persaingan Usaha Malaysia 2010.
Safinaz Mohd Hussein
doaj +1 more source
Evolving Dynamics in Competition Law:A GCC Perspective [PDF]
This article examines the Competition Laws of the Members States of the Gulf Cooperation Council (GCC). It examines their content, puts all of them under general scrutiny from their enactment until today and compares their basic features to other ...
Nora Memeti
doaj +1 more source
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li +5 more
wiley +1 more source

