Results 51 to 60 of about 1,861,033 (245)

Purification and preparation of Marchantia polymorpha Auxin Response Factor 2 for phase separation studies

FEBS Open Bio, EarlyView.
We describe detailed protocols for the purification and preparation of Marchantia polymorpha Auxin Response Factor 2 (MpARF2). This protein is fused to an MBP solubility tag and an mNG fluorescent tag and is purified from Escherichia coli. The presented procedures make it possible to study MpARF2 assemblies, which could arise from phase separation ...
Bas Janssen, Robin Romein, Willy A. M. van den Berg, Simon Lindhoud, Jan Willem Borst, Carlo P. M. van Mierlo   +5 more
wiley   +1 more source

Dynamical analysis of machining tool body with reinforced inner core of circular shape [PDF]

Applied and Computational Mechanics, 2009
The vibration analysis of a clamped beam structure representing vibrating machining body tool is solved in this paper. The required modal properties of beam are obtained by application the reinforcing core with circular cross section.
Naď M.
doaj  

Experiment and numerical analysis on flexural behavior of cold-formed thin-walled C-shaped steel-paper straw board composite floors

Journal of Asian Architecture and Building Engineering, 2023
As a new green material, steel-paper straw board (PSB) composite structures are widely used in practical engineering. This study proposed a new cold-formed thin-walled C-shaped steel-paper straw board (CFCSPSB) composite floor.
Xiuhua Zhang, Hang Li, Zilin Zhao
doaj   +1 more source

Comparative assessment of crystallographic and cryo‐EM models in the Protein Data Bank

FEBS Open Bio, EarlyView.
Raw data obtained by X‐ray crystallography or cryo‐EM result in experimental maps, ultimately fitted by atomic models. Although the physical principles are different, the final results can be viewed, compared, and evaluated in the same way. With cryogenic electron microscopy (cryo‐EM) on track to surpass X‐ray crystallography as the preferred method ...
Alexander Wlodawer, Pawel Rubach, Zbigniew Dauter, Wojciech Dec, Dariusz Brzezinski, Marta Kulik, Wladek Minor, Mariusz Jaskolski   +7 more
wiley   +1 more source

Using fluorescence fluctuation spectroscopy to quantify molecular dynamics within cells

FEBS Open Bio, EarlyView.
Microscopy techniques like fluorescence correlation spectroscopy (FCS) and number and brightness analysis (N&B) allow to quantify concentrations, diffusion rates, and oligomerization of fluorescently labeled molecules in the living cell. In this protocol the principles of how to set up these types of experiments are described including calibration ...
Mark A. Hink
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Flexural Behavior of 3D‐Printed Porous Bouligand‐Structured Polymers: Influence of Pitch Angle and Porosity

Advanced Engineering Materials, EarlyView.
This study examines how helicoidal architectures with different porosities respond to bending. Adjusting layer angle and spacing in 3D‐printed polymers reveals clear tradeoffs between stiffness, strength, and energy absorption. Experiments and simulations highlight designs that distribute stress effectively, offering pathways for optimizing lightweight
Praveenkumar Subhash Patil, Edward D. McCarthy, Parvez Alam   +2 more
wiley   +1 more source

Affecting the Properties of Copper–Graphene Electroconductive Composite by Severe Plastic Deformation

Advanced Engineering Materials, EarlyView.
Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich, Lenka Kunčická, Pavel Czernek, Zifan Wang   +3 more
wiley   +1 more source

Density Measurement of Irradiated and Nonirradiated Zirconium Oxide by Ptychographic X‐Ray Computed Tomography (PXCT)

Advanced Engineering Materials, EarlyView.
Mass density governs the protective behavior of oxide layers on nuclear fuel cladding. Ptychographic X‐ray computed tomography measures zirconium oxide grown on Zircaloy‐4 under reactor and autoclave conditions, revealing nearly identical bulk densities of 5.1 ± 0.80 g cm−3.
Okan Yetik, Liliana I. Duarte, Malgorzata G. Makowska, Roland Brütsch, Andrej Bullemer, Ana Diaz, Mirko Holler, Andreas Menzel, Johannes Bertsch, Pavel Trtik   +9 more
wiley   +1 more source