Results 131 to 140 of about 27,975 (305)
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, EarlyView.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source
Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application
Advanced Engineering Materials, EarlyView.N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang +4 more
wiley +1 more source
Numerical Simulation of Shock Wave Propagation Through Multiple Raindrops
FluidsA numerical study of shock wave propagation through multiple raindrops is presented using a density-based compressible two-phase flow solver coupled with a sharp-interface volume-of-fluid (VoF) method.
Lingquan Li +5 more
doaj +1 more source
Flow Feature Aligned Mesh Generation and Adaptation [PDF]
, 2013 Methods which allow for construction of flow feature aligned meshes in two- and three-dimensions have been developed in this thesis to investigate their potential for improvements in the numerical solution relative to globally refining the mesh.
Harris, Matthew
core
Fundamentals of Compressible Flow Mechanics
, 2021 This book deals with an introduction to the flow of compressible substances (gases). The main difference between compressible flow and almost incompressible flow is not the fact that compressibility has to be considered.
core
Advanced Engineering Materials, EarlyView.Molecular dynamics is used to investigate structure refinement during severe plastic deformation. The results show similitude with experimental data. Molecular dynamics simulations of severe plastic deformation of monocrystalline and polycrystalline samples by multiaxial compression of aluminum are carried out.
Roberto B. Figueiredo
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
AxiomsUnderstanding shear flow behavior in compressible, viscous, micropolar real gases is essential for both theoretical advancements and practical engineering applications.
Nelida Črnjarić, Ivan Dražić
doaj +1 more source
Advanced Engineering Materials, EarlyView.X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky +3 more
wiley +1 more source
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source