Results 181 to 190 of about 1,759,868 (353)

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Experimental Determination of Material Behavior Under Compression of a Carbon-Reinforced Epoxy Composite Boat Damaged by Slamming-like Impact. [PDF]

Polymers (Basel)
Altunsaray E, Biçer M, Karasu HF, Neşer G.   +3 more
europepmc   +1 more source

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

Advanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann, Patrick Schiebel, David May   +2 more
wiley   +1 more source

Investigation on Damage and Energy Absorption Performance of Aluminum Foam Sandwich Plates Under Low-Velocity Impact. [PDF]

Materials (Basel)
Guo K, Zhu Y, Zhou S, Zhu L.
europepmc   +1 more source

Experimental study of the importance of fibre breakage on the strength of thermoplastic matrix composites subjected to compression after impact

Composite structures
F. Naya, J. Pernas-Sánchez, C. Fernández, P. Zumel, M. Droździel-Jurkiewicz, J. Bieniaś   +5 more
semanticscholar   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

Compression-compression fatigue life prediction model of T300/69 laminates under edge impact

Jixie qiangdu
After low-velocity impact at the edge, delamination and matrix extrusion occur inside the composite laminates, which will have a serious impact on the safe use and life of the composite laminates. Therefore, it is of practical engineering significance to
ZHANG Peng, LIU Jianhui, WEI Yaobing
doaj  

Evolutional law and elastoplastic constitutive model of structural loess considering moisture contents. [PDF]

PLoS One
Zhu H, Chen W, An C, Zhang H, Han B, Feng W.   +5 more
europepmc   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Study on radial fracture mechanism of saturated granite subjected to coupled static-cyclic impact loading: An experimental investigation. [PDF]

PLoS One
Wang Y, Liu X, Xu Z, Tang H.
europepmc   +1 more source