Results 21 to 30 of about 95,223 (215)

Does Long‐Term Lower Extremity Strength Training in Adults With Knee Osteoarthritis and Varus Alignment Reduce Knee Joint Loading During Gait?

Arthritis Care &Research, EarlyView.
Objective We examined whether 18 months of strength training in individuals with knee varus alignment and medial tibiofemoral osteoarthritis (OA) reduced knee joint loads during walking compared to an attention control group. Methods This study was a secondary analysis of a randomized clinical trial that compared the effects of strength training to a ...
Stephen P. Messier, Matthew N. Vigliotti, Paige E. Rice, Brian Pietrosimone, Shannon L. Mihalko, Edward H. Ip, Richard F. Loeser, David J. Hunter, Ali Guermazi, Ryan Hill, Santiago Saldana, Kim L. Bennell, Paul DeVita   +12 more
wiley   +1 more source

Moderators of the Effects of Exercise and Manual Therapy for People With Knee and Hip Osteoarthritis: A Secondary Analysis of a Randomized Clinical Trial

Arthritis Care &Research, EarlyView.
Objective This study aimed to investigate potential moderators influencing the effects of manual therapy and exercise therapy on pain and functional outcomes in individuals with knee and/or hip osteoarthritis, using data from the MOA trial. This is a secondary analysis of data from the MOA trial that compares the clinical effectiveness of manual ...
Daniel Cury Ribeiro, Sarah E. Lamb, J. Haxby Abbott   +2 more
wiley   +1 more source

Compressive Strength of Concrete Mixed and Cured with Different Ratios of Fresh and sea Water

, 2023
: By 2025, there will be insufficient drinking water according to a report of the world meteorological organization (WMO). In order to provide drinking water it was found that the use of seawater in the concrete industry was necessary. Researchers in the
Nehal M. Ayash, Magdy M.M. Genedy, Samy Akil Fawzy, Girgis Jacoup Ghattas   +3 more
core   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Effect of distortion on the buckling strength of stiffened panels

, 2009
This paper predicts the behaviour of stiffened plates with different distortion levels in order to address a rational structural design procedure as pre-existing and fabricationrelated (like weld-induced) initial geometrical distortion is of great ...
Das, P.K., Hunt, Stuart, Crow, Anthony, Pretheesh, Paul C., Chaithanya, Pretheesh Paul, Das, Purnendu K.   +5 more
core   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Artificial neural networks in hard tissue engineering : another look at age-dependence of trabecular bone properties in osteoarthritis [PDF]

, 2014
Artificial Neural Network (ANN) model has been developed to correlate age of severely osteoarthritic male and female specimens with key mechanical and structural characteristics of their trabecular bone.
Natasha A Khovanova, Khovanova, N. A., Mallick, Kajal, Shaikhina, Torgyn, Torgyn Shaikhina, Kajal K Mallick   +5 more
core   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source