Results 51 to 60 of about 411,658 (310)
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Prediction of Compressive Strength of Stabilized Earth Block Masonry
Advances in Civil Engineering, 2019 The present study investigates the compressive strength of cement-stabilized earth block masonry prisms with a number of masonry units and joint layer mortar combinations.
Kunasegaram Sajanthan +2 more
doaj +1 more source
Relationship between compressive and tensile strengths of roller-compacted concrete
Journal of Traffic and Transportation Engineering (English ed. Online), 2018 The abstract roller-compacted concrete (RCC) is a zero slump concrete comprising the same materials as that of conventional concrete with different proportions. The RCC must be compacted to reach its final form.
Chamroeun Chhorn +2 more
doaj +1 more source
A study of Compressive Strength Characteristics of Laterite/sand Hollow Blocks [PDF]
, 2007 This paper presents the results of experimental investigations carried out on partial replacement of sand with laterite as it affects the compressive strength of sandcrete hollow blocks. Two mix proportions (1:6 and 1:8) were used with laterite content
Ata, Olugbenga +3 more
core +1 more source
A study on the compressive strength of thick carbon fibre-epoxy laminates [PDF]
, 2007 This paper describes an experimental study that examines the effect of specimen size on the axial compressive strength of IM7/8552 carbon fibre/epoxy unidirectional laminates (UD).
Argon +18 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Fracture mechanisms and failure analysis of carbon fibre/toughened epoxy composites subjected to compressive loading [PDF]
, 2010 This study investigates the failure mechanisms of unidirectional (UD) HTS40/977-2 toughened resin composites subjected to longitudinal compressive loading.
A. Hodzic +19 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source