Results 101 to 110 of about 1,499,819 (348)
Investigation and Analysis of Novel Skewing in a 140 kW Traction Motor of Railway Cars That Accommodate Limited Inverter Switching Frequency and Totally Enclosed Cooling System [PDF]
, 2021 Hyungkwan Jang +5 more
openalex +1 more source
Advanced Engineering Materials, EarlyView.Al‐Cu intermetallic compounds (IMCs) have a significant influence on the properties of Al‐Cu bimetallic interfaces formed in compound casting. This article provides a deeper understanding of microstructure, crystallography, thermal properties, hardness, and corrosion response of Al‐Cu IMCs with the goal of facilitating the optimization of the ...
Alireza Nazarahari +7 more
wiley +1 more source
X‐Ray Tomography Analysis of Damage Mechanisms in Metal Matrix Syntactic Foams During Compression
Advanced Engineering Materials, EarlyView.In situ synchrotron X‐ray tomography is used to investigate the internal damage mechanisms of AlSi12 metal matrix syntactic foam with ceramic hollow spheres during compressive loading. It is concluded that a homogeneous distribution of the second‐phase filler material results in a sequential collapse in a localized region; this leads to controlled and ...
Indrajeet Tambe +8 more
wiley +1 more source
Yield Optimization for The Extraction of Organic Compounds from Okra Leaves Wastes
Diyala Journal of Engineering SciencesAn important area of research is the extraction of organic chemicals from plants and herbs. Considering the fact that the extracts have numerous commercial and pharmacological uses.
Shaimaa Abod Hussain +2 more
doaj +1 more source
Pre-cooling with ingesting a high-carbohydrate ice slurry on thermoregulatory responses and subcutaneous interstitial fluid glucose during heat exposure [PDF]
, 2022 Takashi Naito +5 more
openalex +1 more source
Advanced Engineering Materials, EarlyView.Laser wire directed energy deposition process was leveraged to fabricate large scale NiTi alloy wall. Evaluation of build‐height‐dependent tribo‐mechanical properties revealed significant differences in location specific sample characteristics. The middle region achieved optimal performance (superior wear resistance, balanced strength‐ductility ...
Hyunsuk Choi +5 more
wiley +1 more source
Experimental Analysis and Physics‐Based Analytical Model on Twisted and Coiled Artificial Muscles
Advanced Engineering Materials, EarlyView.Twisted and coiled artificial muscles made from silver‐coated nylon fibers are investigated through experiments and analytical modeling. The actuators achieve contractions up to 19.3% and specific work of 8 kJ kg−1, though efficiency remains limited (≈0.15%) by thermal losses.
Salvatore Garofalo +3 more
wiley +1 more source
A Positron Lifetime Study of Cooling and Natural Aging of Solutionized Aluminum Alloys
Advanced Engineering Materials, EarlyView.The process during cooling of Al–Mg and Al–Mg–Si alloys from the solutionizing temperature down to 20 °C is interrupted. These states are analyzed with positron lifetime spectroscopy to trace the processes during cooling. In different temperature ranges, two stages of vacancy loss and solute clustering are identified.
Zi Yang, Mengjie Li, John Banhart
wiley +1 more source
Scientific ReportsIn a canned motor with a spiral tube heat exchanger for a nuclear main pump, if the secondary water suddenly fails, the temperature of the lubricating water and motor winding insulation must not exceed the alarm or permitted value within the 5 min ...
Li-Kun Ai, Yi-Ping Lu
doaj +1 more source
Optimization of heat sinks with plate fins in air-jet cooling
Nihon Kikai Gakkai ronbunshu, 2014 Heat density of high-load electronics such as high-performance servers and the inverters used in vehicles has been increasing as the result of higher processing speeds and computational scale, and higher output, etc.
Takayuki ATARASHI +2 more
doaj +1 more source