Results 161 to 170 of about 74,264 (312)

ON THE EFFECT OF WATER EVAPORATION ON COOLING EFFICIENCY IN COOLING TOWERS

Известия Томского политехнического университета: Инжиниринг георесурсов, 2019
The paper introduces the results of theoretical study of cooling water droplets as they move in a stream of cold air under conditions characteristic of high-capacity tower cooling towers and the results of a numerical analysis of temperature distributions along the droplet radius.
Sergey A. Shevelev, Natalia N. Zyablova
openaire   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

CFD study of effusion cooling

, 2012
The desire to increase the efficiency, i.e., reduce the\ud specific fuel consumption and raise the thrust-to-weight ratio,\ud of gas turbines has led to an increase in pressure and\ud temperature in the combustion chamber and turbine.
Yang, Zhiyin, Walton, Matthew
core  

Tailoring Functional Properties of Ti–Ni–Cu Shape Memory Alloy Thin Films for MEMS Actuators

Advanced Engineering Materials, EarlyView.
A comprehensive study of critical parameters required to develop well‐performing Ti–Ni–Cu thin film shape memory alloy microactuators is provided. Materials science and device integration aspects are integrated by addressing structural and physical relationships using complementary characterization techniques as well as a practical fabrication solution
Elaheh Akbarnejad, Aleksander Kostka, Gowtham Arivanandhan, Yujiao Li, Alan Savan, Manfred Kohl, Alfred Ludwig   +6 more
wiley   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

Influence of pallet height on energy consumption and cooling effectiveness in an apple cold storage. [PDF]

Sci Rep
Alexander LD, Jakhar S, Dasgupta MS.
europepmc   +1 more source

Cooling Effectiveness of a Modified Cold-Water Immersion Method After Exercise-Induced Hyperthermia. [PDF]

J Athl Train, 2016
Luhring KE, Butts CL, Smith CR, Bonacci JA, Ylanan RC, Ganio MS, McDermott BP.   +6 more
europepmc   +1 more source

THE EFFECT OF HEATING AND COOLING TEMPERATURES ON RAPID COOLING TIME AND

, 2014
In terms of tempering quality, controlling and applying of heating and rapid cooling processes are very important in the glass tempering process. In this study, auto glass tempering process was implemented in the prototype glass tempering unit which was designed specifically, exchange of cooling time and particle number was investigated according to ...
Akcay, M, Sekmen, Y, Golcu, M
openaire   +1 more source