Results 171 to 180 of about 328,365 (310)
Cooling Effectiveness of a Modified Cold-Water Immersion Method After Exercise-Induced Hyperthermia. [PDF]
J Athl Train, 2016 Luhring KE +6 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi +7 more
wiley +1 more source
Investigation of film cooling effectiveness and enhancement of cooling performance
, 2018 Advanced gas turbines are designed to operate at increasingly higher inlet temperatures to increase efficiency and specific power output. This increase in the operating temperature is enabled by advances in high-temperature resistant materials such as super alloys and thermal-barrier coatings (TBCs) and by the development of effective cooling methods ...
openaire +3 more sources
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
Infrared Thermographic Assessment of Cooling Effectiveness in Selected Dental Implant Systems. [PDF]
Biomed Res Int, 2016 Kirstein K +10 more
europepmc +1 more source
Effect of shocks on film cooling of a full scale turbojet exhaust nozzle having an external expansion surface [PDF]
Experimental film cooling data obtained during exploratory testing with an axisymmetric plug nozzle having external expansion and installed on an afterburning turbojet engine in an altitude test facility is presented.
Straight, D. M.
core +1 more source
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
THE EFFECT OF HEATING AND COOLING TEMPERATURES ON RAPID COOLING TIME AND
, 2014 In terms of tempering quality, controlling and applying of heating and rapid cooling processes are very important in the glass tempering process. In this study, auto glass tempering process was implemented in the prototype glass tempering unit which was designed specifically, exchange of cooling time and particle number was investigated according to ...
Akcay, M, Sekmen, Y, Golcu, M
openaire +1 more source
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source