Nuclear Engineering and Technology, 2022 Pool boiling heat transfer is widely applied in nuclear engineering fields. The influence of heating surface orientation on the pool boiling heat transfer has received extensive attention.
Chenglong Wang +6 more
doaj +1 more source
Research On Maximizing Critical And Reducing Initial Heat Flux Densities To Eliminate Any Film Boiling And Minimize Distortion During Quenching [PDF]
, 2017 In the paper the results of testing three types of FUCHS oils: Thermisol QH 120, Thermisol QH 10 and Thermisol QB 46 are discussed. The main attention is paid to critical heat flux densities evaluation because they create a basis for optimizing cooling ...
Dobryvechir, V. (Volodymyr) +3 more
core +2 more sources
Pool Boiling Heat Transfer Characteristics of New and Recycled Alumina Nanofluids
Nanomaterials, 2023 This paper reports an experimental investigation of the heat transfer features of new and recycled Alumina (Al2O3) nanofluids (NFs) in the pool boiling (PB) system.
Wagd Ajeeb, S. M. Sohel Murshed
doaj +1 more source
Saturated Critical Heat Flux in a Multi-Microchannel Heat Sink Fed by a Split Flow System [PDF]
, 2010 An extensive experimental campaign has been carried out for the measurement of saturated critical heat flux in a multi-microchannel copper heat sink. The heat sink was formed by 29 parallel channels that were 199 μm wide and 756 μm deep.
D. Toto +3 more
core +1 more source
Eddy heat fluxes from direct current measurements of the Antarctic Polar Front in Shag Rocks Passage [PDF]
, 2008 Determining meridional heat flux in the Southern Ocean is critical to the accurate understanding and model simulation of the global ocean. Mesoscale eddies provide a significant but poorly-defined contribution to this transport.
Bryden +29 more
core +1 more source
Experimental Study on Thermal Performance of a Bent Copper-Water Heat Pipe
International Journal of Aerospace Engineering, 2020 Vapor-liquid phase change is regarded as an efficient cooling method for high-heat-flux electronic components. The copper-water bent heat pipes are particularly suited to the circumstances of confined space or misplaced heat and cold sources for high ...
Shuangshuang Miao +4 more
doaj +1 more source
Flow boiling in a 1.1mm tube with R134a: Experimental results and comparison with model [PDF]
, 2007 A detailed comparison of the three-zone evaporation model, proposed by Thome et al. (2004), with experimental heat transfer results of two stainless steel tubes of internal diameter 4.26 mm and 2.01 mm using R134a fluid was presented by Shiferaw et al ...
Karayiannis, TG +2 more
core +1 more source
Application of the Critical Heat Flux Look-Up Table to Large Diameter Tubes
Science and Technology of Nuclear Installations, 2013 The critical heat flux look-up table was applied to a large diameter tube, namely 67 mm inside diameter tube, to predict the occurrence of the phenomenon for both vertical and horizontal uniformly heated tubes. Water was considered as coolant.
M. El Nakla +5 more
doaj +1 more source
Effects of surface modifications on pool boiling heat transfer with HFE-7100
International Journal of Thermofluids, 2023 This study explores pool boiling of HFE-7100 on copper surfaces. The key objective of this study was to examine the effects that surface modifications have on nucleate boiling performance.
Genesis Mlakar +2 more
doaj +1 more source
Thermal-hydraulic analysis of light water reactors under different steady-state operating conditions, Part 1: Boiling water reactor [PDF]
Nuclear Technology and Radiation Protection, 2022 The steady-state thermal-hydraulic analysis of the core of the Boiling Water Reactor (BWR/6) at nominal operating conditions is presented in this paper. The BWR/6 is produced by General Electric USA.
Hutli Ezddin, Kridan Ramadan
doaj +1 more source