Results 71 to 80 of about 235,061 (287)
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Limit cycles for piecewise smooth perturbations of a cubic polynomial differential center
Electronic Journal of Differential Equations, 2015 In this article, we study the planar cubic polynomial differential system $$\displaylines{ \dot{x}=-yR(x,y)\cr \dot{y}=xR(x,y) }$$ where $R(x,y)=0$ is a conic and $R(0,0)\neq 0$.
Shimin Li, Tiren Huang
doaj
Numerical treatment of Hunter Saxton equation using cubic trigonometric B-spline collocation method
AIP Advances, 2017 In this article, authors proposed a computational model based on cubic trigonometric B-spline collocation method to solve Hunter Saxton equation. The nonlinear second order partial differential equation arises in modeling of nematic liquid crystals and ...
M. S. Hashmi +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Numerical Continuation and SPDE Stability for the 2D Cubic-Quintic Allen-Cahn Equation
, 2015 We study the Allen-Cahn equation with a cubic-quintic nonlinear term and a stochastic $Q$-trace-class stochastic forcing in two spatial dimensions. This stochastic partial differential equation (SPDE) is used as a test case to understand, how numerical ...
Kuehn, Christian
core +2 more sources
Advanced Engineering Materials, EarlyView.Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller +6 more
wiley +1 more source
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Cubic Spline Solution of linear fourteenth order boundary value problems
Ceylon Journal of Science, 2018 As higher order differential equations have constantly been tiresome and problematic to resolve for the mathematicians and engineers so diverse numerical procedures were conceded out to acquire numerical estimates to such problems.
Aasma Khalid A., M. Nawaz Naeem
doaj +1 more source
A class of cubic differential systems with 6-tuple focus
Journal of Differential Equations, 1990 zbMATH Open Web Interface contents unavailable due to conflicting licenses.
openaire +1 more source