Results 201 to 210 of about 80,443 (263)
Sol-gel and co-precipitation synthesized hybrid nanofluids for enhanced CNC turning of AISI 4340 steel: an experimental and machine learning approach. [PDF]
Sci RepEfa DA +4 more
europepmc +1 more source
Post-dural Puncture Headache: Pathophysiology, Risk Stratification, Prevention, and Evidence-Based Management for Practicing Anesthesiologists. [PDF]
CureusKonduru RA +3 more
europepmc +1 more source
Hybrid cryo-nano MQL strategy for sustainable and high-performance machining of Monel 400. [PDF]
Sci RepRao GN +9 more
europepmc +1 more source
Some of the next articles are maybe not open access.
Related searches:
Related searches:
Contact Dermatitis, 1989
174 consecutive patients with suspected cutting fluid dermatitis were investigated in 2 occupational dermatology clinics. 43% showed allergic reactions which were thought to be relevant to their dermatitis. Irritant contact dermatitis occurred in 63%, but only in 21% was it thought to be the sole diagnosis.
C E, Grattan +3 more
openaire +2 more sources
174 consecutive patients with suspected cutting fluid dermatitis were investigated in 2 occupational dermatology clinics. 43% showed allergic reactions which were thought to be relevant to their dermatitis. Irritant contact dermatitis occurred in 63%, but only in 21% was it thought to be the sole diagnosis.
C E, Grattan +3 more
openaire +2 more sources
Control of cutting fluid in metal cutting and dry cutting
2011 International Conference on Remote Sensing, Environment and Transportation Engineering, 2011A lot of cutting fluid in metal cutting process causes environmental pollution and increases the manufacturing cost. Control of cutting fluid is one of the serious problems that the modern manufacturing technology faces with. This paper describes in brief the development tendency of cutting fluid and its limitations.
null Jianzhong Zhang +2 more
openaire +1 more source
Industrial Lubrication and Tribology, 1974
These authors reported work on cutting oils in our September/October 1972 issue and this paper describes a continuation of their work. The selection of special cutting fluids and lubricants can significantly affect metal cutting operations. Friction forces during metal cutting can increase the amount of work to be done to deform the material, can ...
H. Bagchi, S.K. Basu
openaire +1 more source
These authors reported work on cutting oils in our September/October 1972 issue and this paper describes a continuation of their work. The selection of special cutting fluids and lubricants can significantly affect metal cutting operations. Friction forces during metal cutting can increase the amount of work to be done to deform the material, can ...
H. Bagchi, S.K. Basu
openaire +1 more source
Industrial Lubrication and Tribology, 1987
SYNOPSIS. A new type of cutting fluid is essential to achieving utilisation of the full potential of Automated Machining (AM). Coolant capabilities frequently determine the scope of multi‐tool machining applications. Identifying operational needs and overcoming AM system constraints has provided a unique opportunity to develop a new synthetic cutting ...
openaire +1 more source
SYNOPSIS. A new type of cutting fluid is essential to achieving utilisation of the full potential of Automated Machining (AM). Coolant capabilities frequently determine the scope of multi‐tool machining applications. Identifying operational needs and overcoming AM system constraints has provided a unique opportunity to develop a new synthetic cutting ...
openaire +1 more source
Journal of Fluids Engineering, 1957
Abstract Transfer of radioactive material from a cutting tool to the chips produced in facing the end of a steel tube is used as a means of measuring tool-wear rate. The lathe is operated at commercial feeds and speeds. This technique permits accurate tool-wear evaluation with very short machining time and a consequent small consumption ...
openaire +1 more source
Abstract Transfer of radioactive material from a cutting tool to the chips produced in facing the end of a steel tube is used as a means of measuring tool-wear rate. The lathe is operated at commercial feeds and speeds. This technique permits accurate tool-wear evaluation with very short machining time and a consequent small consumption ...
openaire +1 more source