Micro milling performance assessment of diamond-like carbon coatings on a micro-end mill [PDF]
, 2013 This is the author's accepted manuscript. The final published article is available from the link below. Copyright @ 2013 Institution of Mechanical Engineers.In micro milling, unpredictable tool life and premature tool failures are the major constraints ...
Cheng, K, Wu, T
core +1 more source
A new mechanism for saturating unstable r-modes in neutron stars [PDF]
, 2013 We consider a new mechanism for damping the oscillations of a mature neutron star. The new dissipation channel arises if superfluid vortices are forced to cut through superconducting fluxtubes.
Andersson, Nils +2 more
core +3 more sources
Анализ экологического состояния процесса резания [PDF]
, 2012 В работе рассмотрены экологические аспекты применения жидких СОТС при металлообработке.In this paper ecological aspects of application cutting fluid at cutting are ...
Кириллов, А. К.
core
Effects of distention of the small intestine on the movements of the gallbladder and the sphincter of Oddi [PDF]
, 1969 1. Dogs anesthetized with pentobarbital sodium were mainly used and effects of the distention of the small intestine on the movements of the gall bladder and the sphincter of Oddi were investigated. 2.
Nakayama, Sosogu
core +1 more source
Advances in Mechanical Engineering, 2022 In this work, an innovative nanocutting fluid, based on coconut oil was developed by dispersing silver nanoparticles (AgNPs) of size less than 50 nm. The tribological and physical properties of the prepared nanocutting fluid with different volumes of ...
Rengiah Robinson Gnanadurai +1 more
doaj +1 more source
Pengaruh Penambahan Zat Aditif (Calcium Hypochlorite) terhadap Coolant Properties (Viscosity) Minyak Sawit [PDF]
, 2014 Cutting fluid (coolant) are required in the machining processes. Most of cutting fluid are from mineral oil, and they are as unrenewable resource, therefore look for alternative resources ofmineral oil, which derived from vegetables oil.
HS, I. (Irdoni) +2 more
core
Surface defects in groove milling of Hastelloy-C276 under fluid coolant [PDF]
, 2015 This study aims to investigate surface integrity in groove milling of Hastelloy-C276 using coated carbide end mills under the application of water-based fluid coolant using different cutting parameters. Surface integrity was assessed by measuring surface
Al-Falahi, Muath +3 more
core +1 more source
Grinding Process Results with Oil Mist. [PDF]
, 2016 The paper presents a study of the process of grinding titanium grinding wheels with mikrokorundu, sanding at surfaces involving liquid - cooling lubricants using MQL, used machining fluid - propylene glycol and other liquids business dedicated to the ...
Wejman, Przemysław, Wójcik, Ryszard
core
Modified Jatropha nano-lubricant as metalworking fluid for machining process [PDF]
, 2019 Biodegradable oils that were derived from the nature are renewable sources that may substitute the petroleumbased and synthetic oils. However, the highly viscous Jatropha oil draws upon unsatisfactory lubrication performance in the machining process ...
Abdul Sani, Amiril Sahab +2 more
core
Analysis of the Influence of the Use of Cutting Fluid in Hybrid Processes of Machining and Laser Metal Deposition (LMD) [PDF]
, 2018 Hybrid manufacturing processes that combine additive and machining operations are gaining relevance in modern industry thanks to the capability of building complex parts with minimal material and, many times, with process time reduction.
Arrizubieta Arrate, Jon Iñaki +3 more
core +4 more sources