Results 51 to 60 of about 1,450,593 (288)
Mehmet Akif Ersoy Üniversitesi Fen Bilimleri Enstitüsü, 2020 In this study, cutter vibrations, wear conditions and cutting forces are observed during jet-assisted turning under coolant pressure conditions. Inconel 718 material is used as a thread.
Orhan GÜNGÖR, Hüseyin Bilal MACİT
doaj +1 more source
Investigation of tool geometry effect and penetration strategies on cutting forces during thread milling [PDF]
, 2014 The application of thread milling is increasing in industry because of its inherent advantages over other thread cutting techniques. The objective of this study is to investigate the effect of milling cutter tool geometry on cutting forces during thread ...
Sharma, Vishal S. +4 more
core
Peripheral lysosomes recruit PLEKHG3 to focal adhesions and restrain protrusion dynamics
FEBS Letters, EarlyView.Proximity‐dependent labeling at the LAMTOR complex revealed the Rho GEF PLEKHG3 as a lysosome‐proximal protein directing the study toward the influence of lysosome positioning on actin dynamics and cell motility. We show that PLEKHG3 colocalizes with lysosomes at focal adhesion sites and observe that forced peripheral dispersion of lysosomes hinders ...
Rainer Ettelt +8 more
wiley +1 more source
Advances in Mechanical Engineering, 2015 Minimum quantity lubrication is a technique to have the advantages that cutting fluids bring yet keeping their use at minimum. For the cutting fluids, inedible vegetable oils are potential for minimum quantity lubrication machining.
Mohamed Handawi Saad Elmunafi +2 more
doaj +1 more source
Cutting force prediction in hypoid gear machining
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2016 Hypoid gear machining is a critical process in automobile industries. Many studies have discussed the gear machining in the geometrical model for manufacturing and design of the gears.
Shinichi SHIRAISHI +2 more
doaj +1 more source
Machinability investigation in turning of high density fiberboard. [PDF]
PLoS ONE, 2018 A series of experiments were conducted to assess the machinability of high density fiberboard using cemented carbide cutting tools. The objective of this work was to investigate the influence of two cutting parameters, spindle speed and feed per turn, on
Zhaolong Zhu +5 more
doaj +1 more source
The analysis of cutting forces for hardened steel milling
Омский научный вестник, 2023 Micro milling is a widely used manufacturing method. The main purpose of this study is to analyze the cutting forces in corrosion-resistant, heat-resistant steel 14Kh17N2.
D. S. Makashin
doaj +1 more source
Ligand‐dependent transcriptional heterogeneity in cell cycle gene expression delays G1/S entry
FEBS Letters, EarlyView.EGF and HRG induce distinct G1/S progression programs in ErbB2‐amplified BT474 breast cancer cells. Despite activating the potent ErbB2–ErbB3 heterodimer, HRG does not accelerate cell‐cycle entry. Instead, EGF promotes earlier restriction‐point passage via ERK–FOS signaling, whereas HRG activates the AKT–MYC axis, driving transcriptional heterogeneity ...
Ririn Rahmala Febri +5 more
wiley +1 more source
Synergistic perspectives—How single‐molecule biophysics complement biochemical understanding
FEBS Letters, EarlyView.In this review, we discuss how ensemble biochemistry and single‐molecule approaches are complementary, outline commonly used single‐molecule techniques, and illustrate their relevance through two representative case studies: chromatin organization by SMC complexes and pathway choice during DNA double‐strand break repair.
Sara De Bragança +2 more
wiley +1 more source
Determination of Optimum Machining Parameters in Machining Rene 41 Superalloy Depending on Cutting Speed [PDF]
E3S Web of ConferencesRene 41 superalloy developed to withstand severe mechanical stresses and high temperature operation, and are widely used in aircraft and space vehicles, especially nickel-based ones, due to their high corrosion resistance.
Altin Abdullah +3 more
doaj +1 more source