Results 1 to 10 of about 70,301 (265)

Craniocaudal cyclic load improves risk assessment of lumbar pedicle screw loosening: finite element analysis based on computer tomography [PDF]

open access: yesFrontiers in Bioengineering and Biotechnology
BackgroundPedicle screw loosening (PSL) is a frequent complication in osteoporotic patients undergoing spinal fixation, yet effective risk assessment methods are limited.
Chenyu Jiang   +8 more
doaj   +2 more sources

Strength Assessment of Rectangular Plates Subjected to Extreme Cyclic Load Reversals

open access: yesJournal of Marine Science and Engineering, 2020
The objective of this study is to investigate the strength of the rectangular plates subjected to cyclic load reversals with varying strain ranges. The finite element solution is implemented to estimate the load-carrying capacity.
Mesut Tekgoz, Yordan Garbatov
doaj   +3 more sources

Monotonic and cyclic load of pine wood under uniaxial compression: experiments and modeling [PDF]

open access: yesE3S Web of Conferences, 2023
To analyze the behavior of wood under uniaxial monotonic deformation, we applied an analytical model to separately control of the pre-peak and post-peak branches of the load-displacement curve.
Kolesnikov G.N., Nazarev D.P.
doaj   +1 more source

Cyclic overlay model of py curves for laterally loaded monopiles in cohesionless soil [PDF]

open access: yesWind Energy Science, 2023
The bearing behaviour of large-diameter monopile foundations for offshore wind turbines under lateral cyclic loads in cohesionless soil is an issue of ongoing research. In practice, mostly the p–y approach is applied in the design of monopiles. Recently,
J. Song, M. Achmus
doaj   +1 more source

Load Ratio Effect on Fracture Resistance Curve of SA312 TP304 under Reverse Cyclic Loading Condition [PDF]

open access: yes한국정밀공학회지, 2017
Seismic load induces a reverse cyclic load that alternately applies a tensile and a compressive load to a structure. For nuclear piping material, safety is assessed in terms of fracture toughness.
Sang-Young Kim
doaj   +1 more source

Experimental Investigation of Loading Frequency Influence on a Strength of Asphalt Interlayer Bonding [PDF]

open access: yesArchives of Civil Engineering, 2020
The article presents a new approach to testing the strength of asphalt interlayer bonding. Two loading methods were used: static load and cyclic load. Before carrying out static shear strength tests, the interlayer bonding was subjected to cyclic loads ...
Jarosław Górszczyk, Konrad Malicki
doaj   +1 more source

Study on stress relaxation characteristics of FGH95 powder superalloy treated by laser shock peening

open access: yesMaterials Research Express, 2022
Aiming at the phenomenon that the residual stress induced by Laser Shock Peening (LSP) will relax and redistribute under various loads, temperature, cyclic load, and the dual treatment of temperature and cyclic load on the residual stress relaxation of ...
Haiyan Zhu   +7 more
doaj   +1 more source

Inclination Effect of Cyclic Load Synchronous with Lateral Static Load on Pile Group in Sandy Soil

open access: yesDiyala Journal of Engineering Sciences, 2023
In general Pile foundations are often subject to more than one load in nature. Two loadings, when simultaneous, cause serious problems in the bearing capacity.
Amal S. Gummar , Jasim A. Abbas
doaj   +1 more source

A model test study on the parameters affecting the cyclic lateral response of monopile foundations for offshore wind turbines embedded in non-cohesive soils [PDF]

open access: yesWind Energy Science, 2022
During their service life, monopiles supporting offshore wind turbines are subjected to a large number of lateral cyclic loads resulting from complex environmental conditions such as wind and waves varying in amplitude, direction, load eccentricity and ...
D. Frick, M. Achmus
doaj   +1 more source

Cyclic Loading of Jammed Granular Systems

open access: yesMaterials, 2022
This article describes the cyclic loading of jammed granular systems represented by vacuum-packed particles in compression and tension, focusing on the influence of the properties of the granular material on the mechanical response. A jammed granular system is represented by a cylindrical sample filled with polymer granules (vacuum-packed particles ...
Piotr Bartkowski   +3 more
openaire   +2 more sources

Home - About - Disclaimer - Privacy