Results 171 to 180 of about 109,321 (266)

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Electroplastic Cyclic Deformation of CuZn30 Brass. [PDF]

Materials (Basel)
Weiler W, Jaśkiewicz K, Zimniak Z.
europepmc   +1 more source

The Effects of Straining Frequency and Stress Ratio on Polarization Current Responded to Cyclic Strain in a Commercial Iron

The Effects of Straining Frequency and Stress Ratio on Polarization Current Responded to Cyclic Strain in a Commercial Iron
identifier:oai:t2r2.star.titech.ac.jp ...
openaire  

Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions

Advanced Engineering Materials, EarlyView.
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi, Kimiya Tajik, Harvey Shaw, Matti Isakov, Sami Pajunen, Lauri Rautkari   +5 more
wiley   +1 more source

Bioinspired heliconical auxetic biofibers for intelligent biomechanical surveillance. [PDF]

Sci Adv
Zhou Y, Wang X, Wang Y, Xie L, Qiang Y, Wang W, Li L, Yue O, Liu X.   +8 more
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Effect of heat stress and GlyNAC supplementation on jejunal morphology, hepatic inflammation infiltration and distribution of GSH content in chickens. [PDF]

Poult Sci
Wang C, Jin L, Jia Z, Ma T, Wei Q, Li Y.
europepmc   +1 more source

Effects of stress ratio on striation formation under cyclic loading conditions in polymethyl methacrylate (PMMA)

Effects of stress ratio on striation formation under cyclic loading conditions in polymethyl methacrylate (PMMA)
identifier:oai:t2r2.star.titech.ac.jp ...
openaire  

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Mechanical performance simulation and application of assembled self-centring shear lead damper. [PDF]

Sci Rep
Liu H, Chen Q, Gao Y, Liu S, Liu R, Wen B.   +5 more
europepmc   +1 more source