Results 101 to 110 of about 102,554 (312)
Fluid inertia damper using MR fluid with a long spiral bypass pipe
Mechanical Engineering Journal, 2016 An inertia damper with a long spiral bypass pipe was developed in order to obtain a series inertia effects for vibration suppression of structures in practical use. The damper comprised a cylinder, piston, and MR fluid. The gap was spirally formed around
Taichi MATSUOKA +4 more
doaj +1 more source
Advanced Materials, EarlyView.Ordered three‐dimensional anodic aluminum oxide (3D‐AAO) nanoarchitectures with longitudinal and transverse pores enable architecture‐driven metamaterials. The review maps fabrication advances, including hybrid pulse anodization, and shows how 3D‐AAO templates tailor properties across magnetism, energy, catalysis, and sensing.
Marisol Martín‐González
wiley +1 more source
, 1977 A system is disclosed for using solar energy to heat the interior of a structure. The system utilizes a low cost solar collector to heat a recirculating air mass which then flows through a series of interconnected ducts and passageways without the use of
Jensen, R. N.
core +1 more source
Advanced Materials, EarlyView.An injectable cold atmospheric plasma‐activated decellularized tumor extracellular matrix hydrogel is introduced as a post‐surgical immunoactivation platform. The engineered gel attracts residual tumor cells and induces immunogenic cell death, reshaping the tumor microenvironment and eliciting systemic antitumor immunity. In combination with checkpoint
Tianxu Fang +5 more
wiley +1 more source
Journal of Marine Science and EngineeringOffshore wind turbines (OWTs) are exposed to cyclic loads resulting from wind, waves, and rotor rotation. These loads can induce resonance, thereby significantly increasing the amplitude of the structure and accelerating the accumulation of fatigue ...
Dong-Ju Kim +2 more
doaj +1 more source
A damper for ground wind-induced launch vehicle oscillations [PDF]
, 1975 Prelaunch oscillatory bending deflections of the Atlas/Centaur launch vehicle are restrained by a damper mechanism mounted on the end of a horizontal boom supported from the umbilical tower. A single vertical pin on the vehicle engages the mechanism, and
Bodle, J. G., Hackley, D. S.
core +1 more source
Advanced Materials, EarlyView.Triply‐twinned architected lattices transform deformation from bending to stretching of struts, delivering up to threefold increases in stiffness and strength across polymeric and metallic systems. High‐resolution synchrotron XCT and image‐based simulations reveal how meta‐grain architecture, defects, and AM build orientation govern failure pathways ...
David McArthur +7 more
wiley +1 more source
Positively Charged Polymer‐Brush MOFs for Large‐Area, Pressure‐Resistant Gas Separation Membranes
Advanced Materials, EarlyView.A universal POPA strategy enables positively charged polymer‐brush MOFs with self‐adaptive interfacial interlocking to resist aggregation under fast processing. This design ensures seamless dispersion within large‐area selective layers, achieving 1 m‐wide roll‐to‐roll fabrication of pressure‐resistant MMCMs with tunable CO2 separation performance ...
Yi Yang +11 more
wiley +1 more source
Design and simulation of a controller for an active suspension system of a rail car
Cogent Engineering, 2018 The quest to increase the performance of rail car in terms of stability, safety and ride comfort has triggered research into the design, modelling and dynamic simulation of the suspension system of a rail car.
I. A Daniyan, K. Mpofu, D. F. Osadare
doaj +1 more source
Advanced Materials, EarlyView.This review highlights the role of self‐assembled monolayers (SAMs) in perovskite solar cells, covering molecular engineering, multifunctional interface regulation, machine learning (ML) accelerated discovery, advanced device architectures, and pathways toward scalable fabrication and commercialization for high‐efficiency and stable single‐junction and
Asmat Ullah, Ying Luo, Stefaan De Wolf
wiley +1 more source