Results 161 to 170 of about 1,066,939 (299)

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Effect of yield locus exponent on draw-in prediction during deep drawing of commercially pure titanium. [PDF]

Sci Rep
Gassler L, Hirsch A, Afrasiabi M.
europepmc   +1 more source

The testing of steel for deep drawing [PDF]

, 1966
Pearce, Roger
core  

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Experimental Study on Deep-Drawing Dies Made of Pre-Stressed UHPC. [PDF]

Materials (Basel)
Holzer K, Zhang Y, Martinitz L, Hoyer J, Volk W.   +4 more
europepmc   +1 more source

Abrasive Wear between Rough Surfaces in Deep Drawing [PDF]

, 2002
Masen, M.A., Rooij, M.B. de
core   +1 more source

Numerical Modeling of Tank Cars Carrying Hazardous Materials With and Without Composite Metal Foam

Advanced Engineering Materials, EarlyView.
Large‐scale puncture models consisting of hazardous materials (HAZMATs) tank car with protective steel–steel composite metal foam (S–S CMF) are solved numerically. Tank car plate with added 10.91–13.33 mm thick S–S CMF layer does not puncture. Protective S–S CMF absorbs impact energy, reduces plate deformation, and prevents shear bands formation ...
Aman Kaushik, Afsaneh Rabiei
wiley   +1 more source

Improving Deep Drawing Quality of DD13 Sheet Metal: Optimization of Process Parameters Using Box-Behnken Design. [PDF]

Materials (Basel)
Celik I, Şensoy AT, Seven G, Cicek D.
europepmc   +1 more source

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Study on Formability and Microstructure Evolution of Usibor^®2000 Sheet Under Different Forming Temperatures in Deep Drawing Process. [PDF]

Materials (Basel)
Wang Y, Hou J, Deng P, Shi Y, Song J.
europepmc   +1 more source