Results 91 to 100 of about 3,006,278 (248)
Advanced Engineering Materials, EarlyView.CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz +4 more
wiley +1 more source
3D MODELING FOR CAR BODY DESIGN
Journal of Industrial Design and Engineering Graphics, 2013 The purpose of this article is to present the method of designing the body of a car. There are several ways to create the exterior shape of a car, but in the following part we will use 3D StudioMax .
ISPAS Marius
doaj
Design of a Multistable Finger Prosthesis with Programmable Metamaterials
Advanced Engineering Materials, EarlyView.This research article shows the development of a multistable programmble metamaterial for the use as a finger prosthesis. The material was designed on different hierarchical levels where the influence of geometrical parameters and combination of mechanical elements was explored.
Franziska Wenz +5 more
wiley +1 more source
DESIGN OF A UNIVERSAL LIFTING EQUIPMENT AND ITS ADAPTABILITY
Journal of Industrial Design and Engineering Graphics, 2014 The paper presents the design of a lifting equipment following the 7 principles of Universal Design. The 7 principles of Universal Design guide engineers, designers and constructors to create products that can satisfy a vast range of users necessities ...
ALIMAN Alina
doaj
Advanced Engineering Materials, EarlyView.This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji +3 more
wiley +1 more source
GRAPHIC-ANALYTICAL METHODS FOR CALCULATING THE GRAVITY CENTER OF A MODEL AIRPLANE
Journal of Industrial Design and Engineering Graphics, 2012 This paper presents a stage of the realization of an airplane capable to work with low capacity motors between 2.5 cmc and 4 cmc, as it presents the gravity center calculation. Firstly for an airplane to fly properly we must calculate the gravity center,
DIACONESCU Olivian
doaj
Interactive textbook of descriptive geometry
, 2011 An aim of this diploma thesis is to create interactive descriptive geometry coursebook. As a basis for coursebook creation was used "Present State of Descriptive Geometry Education on High Schools Survey" which was proceeded via questionnaire. Before the
Krsová, Michaela
core
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
VARIATIONS OF CONCAVE PYRAMIDS OF SECOND SORT WITH AN EVEN NUMBER OF BASE SIDES
Journal of Industrial Design and Engineering Graphics, 2015 Concave pyramids of second sort (CP II) are formed similarly to concave cupolae of second sort (CC II) with a comparable logic of emergence to the regular-faced convex pyramids.
OBRADOVIĆ Marija +2 more
doaj
Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam
Advanced Engineering Materials, EarlyView.Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva +2 more
wiley +1 more source