Results 81 to 90 of about 18,180 (265)

DESIGN OF A UNIVERSAL LIFTING EQUIPMENT AND ITS ADAPTABILITY

Journal of Industrial Design and Engineering Graphics, 2014
The paper presents the design of a lifting equipment following the 7 principles of Universal Design. The 7 principles of Universal Design guide engineers, designers and constructors to create products that can satisfy a vast range of users necessities ...
ALIMAN Alina
doaj  

Microstructure‐Controlled Crack Propagation and Fracture Resistance in MoSiBTiC Alloy Revealed by Multiscale Extended Finite Element Method Modeling

Advanced Engineering Materials, EarlyView.
A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du, Takahiro Kaneko, Xinyu Yan, Takahito Ohmura, Kyosuke Yoshimi   +4 more
wiley   +1 more source

GRAPHIC-ANALYTICAL METHODS FOR CALCULATING THE GRAVITY CENTER OF A MODEL AIRPLANE

Journal of Industrial Design and Engineering Graphics, 2012
This paper presents a stage of the realization of an airplane capable to work with low capacity motors between 2.5 cmc and 4 cmc, as it presents the gravity center calculation. Firstly for an airplane to fly properly we must calculate the gravity center,
DIACONESCU Olivian
doaj  

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

VARIATIONS OF CONCAVE PYRAMIDS OF SECOND SORT WITH AN EVEN NUMBER OF BASE SIDES

Journal of Industrial Design and Engineering Graphics, 2015
Concave pyramids of second sort (CP II) are formed similarly to concave cupolae of second sort (CC II) with a comparable logic of emergence to the regular-faced convex pyramids.
OBRADOVIĆ Marija, MIŠIĆ Slobodan, POPKONSTANTINOVIĆ Branislav   +2 more
doaj  

Slip Localization Intensification Mediated by Grain Boundary Sliding in a Polycrystalline Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat, D. Anjaria, I. Woo, C. Bean, D. Texier, J. C. Stinville   +5 more
wiley   +1 more source

ERGONOMIC DESIGN OF AIRCRAFT COCKPIT

Journal of Industrial Design and Engineering Graphics, 2011
This paper presents a model for an ergonomic design of an aircraft cockpit with the specification and verification with respect to the new European Aviation Safety Agency (EASA) and Federal Aviation Administration (FAA) requirements.
CÎMPIAN Ionuţ
doaj  

Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales

Advanced Engineering Materials, EarlyView.
Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik, Alexander Jelinek, Markus Alfreider, Jutta Luksch, Anton Hohenwarter, Florian Schaefer, Christian Motz, Daniel Kiener   +7 more
wiley   +1 more source

THE INTERSECTION OF CYLINDRICAL SURFACES GRAPHO-ANALYTICAL STUDIES

Journal of Industrial Design and Engineering Graphics, 2008
This paper presents the determination of the section curve of two rotation cylinders with intersecting axes and parallel with a projection plane, using the analytical method, as well as the graphical method (of auxiliary spheres).
MARIN Dumitru
doaj  

A Lightweight Procedural Layer for Hybrid Experimental–Computational Workflows in Materials Science

Advanced Engineering Materials, EarlyView.
We unveil a prototype hybrid‐workflow framework that fuses automatedcomputation with hands‐on experiments. Built atop pyiron, a lightweight, parameterized layer translates procedure descriptions into executable manual steps, syncing instrument settings, human interventions, and data capture in real‐time today.
Steffen Brinckmann, Sarath Menon, Raphael Röske, Johannes Steinhülb, Michael Selzer, Jan Janssen, Tilmann Hickel, Ruth Schwaiger, Jörg Neugebauer   +8 more
wiley   +1 more source