Results 71 to 80 of about 363 (184)
Geology of the central uplift of the Kamestastin Lake impact structure, Labrador, Canada
Abstract The ~28 km Kamestastin (Mistastin) Lake impact structure is a relatively well‐preserved and well‐exposed complex impact structure. The central uplift of this structure is accessible as two islands in the middle of Kamestastin Lake. We present an updated, detailed geological map and description of Horseshoe and Bullseye islands that provides ...
A. C. Singleton, G. R. Osinski
wiley +1 more source
Formation of Metallic Glass Coatings by Detonation Spraying of a Fe66Cr10Nb5B19 Powder
The present work was aimed to demonstrate the possibility of forming Fe66Cr10Nb5B19 metallic glass coatings by detonation spraying and analyze the coating formation process. A partially amorphous Fe66Cr10Nb5B19 powder with particles ranging from 45 µ
Ivanna D. Kuchumova +15 more
doaj +1 more source
ABSTRACT A recent raft of due diligence regulation (DDR) addressing social and environmental conditions in global value chains (GVCs) has spread across the UK and Europe. An emerging literature on DDR highlights the politics of its formation. Yet, we know little about how existing sustainability governance along GVCs interacts with DDR or the wider ...
Matthew Alford +4 more
wiley +1 more source
Effects of Heat and Momentum Gain Differentiation during Gas Detonation Spraying of FeAl Powder Particles into the Water. [PDF]
Senderowski C +6 more
europepmc +1 more source
Insects and Survival: A Review of Primary and Secondary Defense Strategies
Based on a review of three decades of literature, insect defense mechanisms are classified into primary (I) and secondary (II) mechanisms of behavioral, morphological, and chemical nature. These mechanisms have been recorded in 22 (I) and 20 (II) orders, respectively.
Lucas Fernandes Silva +3 more
wiley +1 more source
STRUCTURE AND ASPECTS OF AMORPHOUS DETONATING COVERS ARE BASED ON IRON
The structure and properties of the stratified amorphous coatings obtained in the conditions of thermal spraying are considered in the article. The comparative analysis of coatings from iron-based alloys is presented.
V. V. Artemchuk
doaj
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
This study presents the experimental results of high-temperature oxidation testing under actual operating con ditions in a thermal power plant of gradient and homogeneous composite NiCr–Al coatings produced by the detonation spraying method.
M. Maulet +3 more
doaj +1 more source
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
Characteristics of Al Coatings Fabricated by Detonation Gun Spray on Polymer-based Composites
0.45mm thick Al coatings were deposited by detonation gun spraying (D-gun) on polymer-based composites. The characteristics of the coatings, including micro structure, phase composition and bonding strength, were investigated by means of SEM, EDS, XRD ...
CUI Yong-jing +4 more
doaj +1 more source

