Results 31 to 40 of about 7,561 (264)

Discordance Between Systemic Lupus Erythematosus Disease Activity Index Domain Weights and Their Association With Organ Damage Accrual

Arthritis Care &Research, EarlyView.
Objective Studies of damage accrual in patients with systemic lupus erythematosus (SLE) show associations with disease activity measured by the SLE Disease Activity Index 2000 (SLEDAI‐2K), but these associations are imperfect. SLEDAI scores are powerfully influenced by weightings (1–8) assigned to each domain.
Kevin Zhang, Eric F. Morand, Sarah E. Boyd, François Petitjean, Alberta Hoi, Rachel Koelmeyer, Iolanda Miceli, Julie A. Monk, Hieu T. Nim   +8 more
wiley   +1 more source

Die-Casting Conditions for Pure Aluminum Heat Sink with Thin Fins

Metals
Heat sinks with thin and tall fins made from pure aluminum using die casting are in demand due to the higher thermal conductivity of pure aluminum compared to aluminum alloys.
Hiroshi Fuse, Toshio Haga
doaj   +1 more source

Incidence, Risk Factors and Management of Adverse Events in Contemporary Real‐World Care of Children with Juvenile Idiopathic Arthritis

Arthritis Care &Research, Accepted Article.
Objective We describe the frequency, risk factors, severity, and management of actionable and serious adverse events (AAE and SAE) in children with newly diagnosed Juvenile Idiopathic Arthritis (JIA) in Canada. Methods We enrolled patients within 3 months of JIA diagnosis in the Canadian Alliance of Pediatric Rheumatology Investigators (CAPRI) Registry,
Bashayer Alnuaimi, Roberta A. Berard, Jean‐Philippe Proulx‐Gauthier, Heinrike Schmeling, Michelle Batthish, Gilles Boire, Adam M. Huber, Dax G. Rumsey, Jaime Guzman, Gaëlle Chédeville, The CAPRI registry Investigators   +10 more
wiley   +1 more source

Temperature change and stress distribution analysis of die surface in Al-alloy die casting process and experimental study on die heat check [PDF]

China Foundry, 2008
The temperature change of the die surface in practical aluminum alloy die casting process was analyzed,and a 2D model was formulated on the basis of a deep concave round cavity without sliding core to analyze the stress distributions along the die ...
Hu Xinping, Zhao Guoqun, Wu Bingyao
doaj  

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Effects of heat treatment on microstructure and mechanical properties of squeeze casting AlSi9Mg alloy flywheel housings formed with local supplementary pressure

Journal of Materials Research and Technology
Targeted squeeze casting components of the thick-walled locations with local supplementary pressure (LSP) can effectively realize the local forced shrinkage, which is very significant for the elimination of shrinkage defects.
Jufu Jiang, Lingbo Kong, Yingze Liu, Ning Ge, Ying Wang, Changjie Ding, Dechao Zou   +6 more
doaj   +1 more source

Failures of dies for die-casting of aluminium alloys [PDF]

Metalurgija, 2008
Die-casting dies for casting of aluminum alloys fail because of a great number of different and simultaneously operating factors. Material selection, die design, and thermal stress fatigue generated by the cyclic working process (heat checking), as well ...
Kosec, B.
doaj  

Hypoeutectic Al-Si Alloy with Cr, V and Mo to Pressure Die Casting

Archives of Foundry Engineering, 2017
This paper presents the results of hypoeutectic 226 grade alloy as well as prepared on its basis Al-Si alloy containing Cr, V and Mo. The additives tested were added as AlCr15, AlV10 and AlMo8 master alloys.
Szymczak T., Gumienny G., Stasiak I., Pacyniak T.   +3 more
doaj   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Influence of automation of the process of producing castings by the method of casting under high pressure on the quality of castings

Литьë и металлургия
This paper presents various approaches to automation in high‑pressure die casting and analyzes its impact on casting quality. It has been established that automation in the die casting process not only reduces the labor intensity of production but also ...
V. I. Chechukha, M. A. Sadokha
doaj   +1 more source